Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
TFA_No. 60.4519_Anl_07_23
12.07.2023
Radio controlled clock with indoor temperature
4. Elements
A: LCD display (Fig. 1):
A 1:
Time
A 3:
Snooze symbol
A 5:
Alarm symbol
A 7:
Battery symbol
A 9:
Time zone symbol
A 11: Indoor temperature
A 13: Date
B: Buttons (Fig. 2):
B 1:
MODE button
B 3:
ALARM button
B 5:
DOWN button
C: Housing (Fig. 2):
C 1:
Wall mounting hole
C 3:
Battery compartment
5. Getting started
5.1 Insert the batteries
• Remove the protective film from the display.
• Open the battery compartment by lifting up the holder and pulling down the battery compartment lid. Insert two new AA
1.5 V batteries, polarity as illustrated.
• The device will alert you with a beep and all LCD segments will be displayed for a short moment. Close the battery cover
again.
5.2 Radio-controlled time reception
• The clock will now scan the DCF frequency signal and the DCF symbol flashes on the display. When the time code is suc-
cessfully received after some minutes, the radio-controlled time and the DCF symbol will be shown steadily on the display.
In Daylight Saving Time S is shown on the display.
• If there is no reception, you can start the initialisation manually. Press and hold the WAVE button for three seconds.
• The DCF symbol flashes.
• Interrupt the reception by pressing the WAVE button again for three seconds. The DCF reception symbol disappears.
• The DCF reception always takes place daily at 1:00, 2:00, 3:00, 4:00 and 5:00 o'clock in the morning.
14
11:03 Uhr
Seite 8
A 2:
Year setting
A 4:
Alarm mode
A 6:
DCF reception symbol
A 8:
Symbol Daylight Saving Time (DST) symbol
A 10: Seconds/calendar week
A 12: Day of the week
B 2:
WAVE button
B 4:
UP button
C 2:
Stand (fold out)
Radio controlled clock with indoor temperature
• There are three different reception states:
flashing – Reception is active
remains – Reception is successful
disappears – No reception
• If the clock cannot detect the DCF-signal (e.g. due to interference, transmitting distance, etc.), the time can be set manually.
5.3 Note on radio-controlled time
• The time is transmitted from an atomic clock near Frankfurt am Main by a DCF-77 (77.5 kHz) frequency signal with a range
of about 1,500 km. Your radio-controlled clock receives the signal, converts it and always shows the exact time. The adjust-
ment of Daylight Saving Time and Standard Time is also automatic.
• Make sure to avoid the vicinity of any source of interference such as computer screens, TV sets or solid metal objects.
Within concrete walls (reinforced with steel) such as basements, the received signal is naturally weakened. In extreme
cases, please place the unit close to a window to improve reception.
• During night-time, the atmospheric interference is usually less severe. A single daily reception is adequate to keep the accu-
racy deviation under 1 second.
6. Operation
6.1 Manual settings
• Press and hold the MODE button for three seconds to enter the setting mode.
• The first adjustable value flashes on the display.
• Use the UP or DOWN button to make the desired setting.
• Confirm with the MODE button and go to the next setting.
• The sequence is shown as follows:
– Year, month, day
– Hours, minutes
– Day-of-week language: (default: German)
– DCF reception on/off (default: RCC ON)
• Press and hold the UP or DOWN button in the respective setting mode for quick setting. The device will automatically quit
the setting mode if no button is pressed for 15 seconds.
6.1.1 Day-of-the week language
• In the setting mode you can choose between the day-of-the week language: German (GER), French (FRE), Spanish (SPA),
Italian (ITA), Danish (DAN), Dutch (DUT), Swedish (SWE), English (ENG).
15
Advertenties
Inhoudsopgave
