Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
6.1. Memory storing the 868 MHz radio controls
You can memory store up to a maximum of 250 codes, subdivided between the two channels, OPEN and
OPEN/CLOSE.
1.
On the radio control simultaneously press and hold down push-buttons P1 and P2 (see the instructions of the radio
control).
2.
After about one second, the LED of the radio control begins to flash.
Release both push-buttons.
3.
4.
Press and hold down push-button OP or O/C on the board to memory store, respectively the OPEN or OPEN/CLOSE
channel. The relevant LED begins to flash.
5.
Simultaneously press the push-button of the radio control with which you wish to associate the selected command.
6.
Check if the LED relating to the command being memory stored (DL7 for the OPEN channel or DL6 for the OPEN/CLOSE
channel) lights up with steady beam for about two seconds to confirm correct memory storage.
7.
To finish programming, press twice, in brief succession, the push-button of the memory-stored radio control.
The automated system will perform an opening manoeuvre – make sure that there are no obstacles inside the operating
range.
8.
To memory store the other channel, repeat the whole procedure from point 1.
To add other radio controls, transfer the code of the memory-stored push-button of the radio control to the relevant
push-button of the radio controls to be added, observing the following procedure:
•
On the memory-stored radio control, simultaneously press and hold down push-buttons P1 and P2 (see instructions of the
radio control).
•
The LED of the radio control begins to flash.
•
Release both push-buttons.
•
Put the two radio controls frontally into contact.
•
On the memory-stored radio control press and hold down the push-button relating to the channel you wish to transfer – the
LED of the radio control lights up on steady beam.
•
On the radio control to be memory stored, press the required push-button and release it after the radio control has flashed
twice.
•
To finish programming, press twice in brief succession, the push-button of the memory-stored radio control.
The automated system will perform an opening manoeuvre – make sure that there are no obstacles inside the operating
range.
6.2. Memory storing the 433 MHz radio controls
You can memory store up to a maximum of
You can memory store up to a maximum of 250 codes, subdivided between the two channels, OPEN and
OPEN/CLOSE.
1.
On the control unit, press the push-button of the channel you wish to memory store, OP for the OPEN channel or O/C
for the OPEN/CLOSE channel.
2.
The relevant LED on the control unit begins to flash – release the push-button.
3.
On the radio control, press the push-button with which you wish to associate the selected channel.
The LED on the control unit lights up on steady beam for about one second, signalling that the radio control was stored
4.
in the memory, then it resumes flashing.
5.
During this stage further radio controls can be stored in the memory.
6.
After about 10 seconds the control unit automatically exits the learning phase.
7.
To add other radio controls or to memory store the second channel, repeat the operations from point 1
6.2.1. r
emote memory storAge oF
Other radio controls can be remotely stored only with the 433 MHz radio controls, i.e. without using the push-buttons of the
control unit, but using a previously memory-stored radio control.
1.
Get a radio control already memory stored on one of the 2 channels.
2.
Step near the automated system.
3.
Simultaneously press and hold down push-buttons P1 and P2 (see instructions of the radio control) for about 5 seconds.
4.
Within 5 seconds press, on the memory-stored radio control, the push-button you wish to transfer to the new radio control.
In this way the learning phase for the selected channel is activated on the control unit.
5.
Within 5 seconds, press on the new radio control, the push-button you wish to associate with the selected channel.
6.
After the new radio control has been stored in the memory, the control unit keeps the learning mode active on the
selected channel for about 5 seconds.
During these 5 seconds, other radio controls can be memory stored on the control unit, as ever associated with the
7.
activated channel.
8.
When 5 seconds have elapsed from memory-storage of the last radio control, the control unit automatically exits the
learning stage.
9.
To check if the radio control was correctly memory stored, wait for 5 seconds after sending the code.
6.3. Deleting the radio codes
To delete all the radio control codes stored in the memory, perform the following procedure:
Press and hold down one of the two push-buttons OP or O/C.
1.
2.
The relevant LED begins to flash.
3.
After five seconds, the LED starts to flash at high speed.
4.
After other five seconds both LEDs, DL6 and DL7 light up on steady beam.
5.
Release the push-button.
433
mhz rAdio controls
LYNX 08 24V
Page 2
Guide for the installer
Advertenties
Hoofdstukken
Inhoudsopgave
