Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
prevention regulations in force in your area, as
well as all other general rules of health and safety
at work, is imperative. The manufacturer's liability
shall be deemed void if the machine is modifi ed in
any way and the manufacturer shall therefore ac-
cept no liability for any damages arising as a re-
sult of modifi cations. Even if the machine is used
as intended, certain residual risk factors cannot
be completely eliminated. For reasons of design
and the construction of the machine, the following
eventualities are possible:
•
Contact with the diamond cutting wheel whe-
re it is not covered.
•
Contact with the diamond cutting wheel while
it is turning.
•
Defective diamond tips flying off the cutting
wheel.
•
Workpieces or parts of workpieces kicking
back.
•
Damage to hearing if the ear-muffs specified
are not used.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
5. Before starting the equipment
•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the diamond wheel to
run freely.
•
Before you actuate the ON/OFF switch, make
sure that the diamond wheel is correctly fit-
ted and that the machine's moving parts run
smoothly.
•
Before you connect the machine to the power
supply, make sure the data on the rating plate
is the same as that for your mains.
•
Before using the machine, check all of the
parts for damage and replace any parts that
are damaged. When replacing any parts or
accessories, always carefully follow the inst-
ructions in this manual.
•
For optimum performance and maximum sa-
fety, keep the machine clean at all times.
•
Check the machine cable at regular intervals.
•
While the machine is running, check the wea-
Anl_TC_TC_800_SPK13.indb 16
Anl_TC_TC_800_SPK13.indb 16
GB
ring parts and the fastenings of parts which
may have become loose and check that all
accessories are correctly fitted.
•
Notice! The tile cutting machine is desig-
ned for use with water.
•
Check that the water level is high enough to
cover the diamond part of the wheel each
time before you start a cutting operation and
keep checking it during cutting as well. Fill/
refill the cooling water directly into the trough.
5.1 Assembly (Fig. 1/9)
Assemble the equipment as shown in fi gures
1/2/3/7/9.
5.2 Changing the diamond cutting wheel
(Fig. 2/3)
To replace the wheel when worn, proceed as
follows:
•
Pull out the power plug first.
•
Remove the side cover (17).
•
Apply an 8 mm counterholder to block the
motor shaft.
•
Unscrew the lock nut (18) on the wheel flange
(16) with a 19 mm wrench.
•
Clean the wheel flange thoroughly once the
wheel has been removed.
•
Mount the new diamond cutting wheel on the
cleaned flange, fit the outer flange (16) and
tighten with the nut (18).
•
Fasten the side cover (17) again.
Check that the diamond wheel rotates in the
correct direction!
5.3 Adjusting the top wheel guard (Fig. 4)
•
Move the wheel guard to approximately 5 mm
above the tile you wish to cut. Lock the wheel
guard (3) in position with the knurled screw
(9) as shown in Fig. 1.
•
Notice!The machine is fitted with a cutting
wheel with a non-segmented edge.
5.4 Filling the cooling water tank (Fig. 8)
•
Fill the tank as far as the corresponding mar-
kings (Fig. 8).
- 16 -
11.04.2023 14:14:53
11.04.2023 14:14:53
Advertenties
Inhoudsopgave
