Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
3. Technical data
AC motor .................................220-240 V~ 50 Hz
Motor rating: ............................. 800 W S2 10 min
Motor speed: ........................................ 2990 rpm
Insulation material class .......................... Class F
Protection type .............................................IPX4
Protection class ................................................. I
Cut length: ............................................ Unlimited
Jolly length: .......................................... Unlimited
Cutting height 90°: .................................... 34 mm
Cutting height 45°: .................................... 14 mm
Cutting table-Dimensions ....... 395 mm x 385 mm
Diamond cutting wheel ........... ø 180 x ø 25.4 mm
Weight: .......................................................9.2 kg
A load factor of S2 10 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (800 W)
for no longer than the time stipulated on the spe-
cifi cations label (10 minutes ON period). If you fail
to observe this time limit the motor will overheat.
During the OFF period the motor will cool again to
its starting temperature.
Danger!
Noise
The noise emission values were measured in ac-
cordance with EN 60204.
Operation
L
sound pressure level ..................... 80.6 dB(A)
pA
K
uncertainty ..................................... 2.5 dB(A)
pA
L
sound power level ...................... 100.6 dB(A)
WA
K
uncertainty ..................................... 2.5 dB(A)
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
Warning:
The noise emission levels may vary from the level
specifi ed during actual use, depending on the
way in which the power tool is used, especially
the type of workpiece it is used for.
Anl_TC_TC_800_SPK13.indb 15
Anl_TC_TC_800_SPK13.indb 15
GB
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
4. Intended use
The tile cutting machine is designed for the
standard cutting of small and medium-size tiles
(glazed tiles, ceramic tiles or similar) which can
be accommodated by the size of the machine. It
is designed for DIY applications and craft busi-
nesses in particular. It should never be used for
cutting wood or metal.
The machine should be used exclusively for its
intended purpose. No other use is permitted
and the manufacturer will not accept liability for
any damages or injury resulting from any such
use; responsibility rests with the user/operator
in any such case. Only use cutting wheels which
are suitable for the machine. Saw blades should
never be used. Compliance with the safety inst-
ructions, the assembly instructions, and advice
and instructions on operation contained in the
operating instructions also falls under the terms
of intended use. All persons operating or carrying
out maintenance work on the machine must be
acquainted with the above and be aware of all
potential dangers.
In addition, strict compliance with the accident
- 15 -
11.04.2023 14:14:53
11.04.2023 14:14:53
Advertenties
Inhoudsopgave
