Advertenties
Beschikbare talen
Beschikbare talen
Protection type
Weight of the unit in kg
Oil (15W 40) l
Max. altitude
(above mean sea level)
The noise emission values were measured in ac-
cordance with EN ISO 3744.
Wear hearing protection.
The effects of noise can cause a loss of hearing.
7. Before starting the equipment
Before you connect the equipment to the mains supply
make sure that the data on the rating plate are identical
to the mains data.
• Check the equipment for damage which may have
occurred in transit. Report any damage immediately
to the transport company which was used to deliver
the compressor.
• Install the compressor near the point of consumption.
• Avoid long air lines and supply lines (extension ca-
bles).
• Make sure that the intake air is dry and dustfree.
• Do not install the compressor in a damp or wet room.
• The compressor may only be used in suitable rooms
(with good ventilation and an ambient temperature
from +5 °C to 40 °C). There must be no dust, acids,
vapors, explosive gases or inflammable gases in the
room.
• The compressor is designed to be used in dry rooms.
It is prohibited to use the compressor in areas where
work is conducted with sprayed water.
• The oil level in the compressor pump has to be
checked before putting the equipment into operation.
8. Attachment and operation
m Important!
You must fully assemble the appliance before using it
for the first time!
You will require the following tools for assembly and in-
stallation: 2 x open-ended wrench size 19 mm (not in-
cluded)
You will require the following tools for assembly and in-
stallation: 2 x open-ended wrench size 14 mm (not in-
cluded)
8.1 Fitting the wheels (Fig. 5)
• Fit the supplied wheels (11) as shown.
8.2 Fitting the supporting foot (2x)(Fig. 6)
• Fit the supplied supporting foot (2x) as shown.
38
GB
IP20
8.3 Fitting the air filter (2x)(Fig. 7,8)
approx. 52.7
• Remove the transportation stop (A) and screw the air
approx. 0,25
1000 m
8.4 Changing the transportation cover (B) (Fig. 9,10)
• Remove the transportation cover from the oil filter
8.5 Mains connection
• The compressor is equipped with a mains cable with
• Before you use the machine, make sure that the
• Long supply cables, extensions, cable reels etc.
• At low temperatures below +5°C, sluggishness may
8.6 ON/OFF switch (Fig. 2)
• Pull the ON/OFF switch (16) upwards to switch on the
8.7 Setting the pressure (Fig. 1,3)
• Use the pressure regulator (5) to set the pressure on
• The set pressure can be drawn from the quick lock
• The vessel pressure can be read off the pressure
• The vessel pressure is drawn from the quick lock cou-
8.8 Setting the pressure switch (Fig. 1)
• The pressure switch (2) is set at the factory. Cut-in
8.9 Overload switch (Fig. 14)
The motor is fitted with an overload switch (18). If the
compressor overloads, the overload switch switches off
the equipment automatically to protect the compressor
from overheating. If the overload switch triggers, switch
off the compressor using the ON/ OFF switch (16) and
wait until the compressor cools down. Then press the
overload switch (18) and restart the compressor.
9. Electrical connection
The electrical motor installed is connected and ready for
operation. The connection complies with the applicable
VDE and DIN provisions.
The customer's mains connection as well as the exten-
sion cable used must also comply with these regula-
tions.
filter (14) to the equipment.
opening (19) and insert the supplied oil sealing plug
(15) into the oil filler opening.
shock-proof plug. This can be connected to any 230-
240V ~ 50 Hz shock-proof socket.
mains voltage is the same as the operating voltage
(see the rating plate).
cause a drop in voltage and can impede motor start-
up.
make starting difficult or impossible.
compressor. To switch off the compressor, press the
ON/OFF switch down.
the pressure gauge (4).
coupling (3).
gauge (6).
pling (7).
pressure approx. 6 bar Cut-out pressure approx. 8
bar.
Advertenties
