Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
2. Layout (Fig. 1)
1. Charger
2. Charging cable
3. Technical data
Charger
Input ........................ 220-240V~50-60Hz, 150 W
Output 1 ............................... 18 V d.c., 3000 mA
Output 2 ............................... 18 V d.c., 3000 mA
Caution!
The charging unit is allowed to be used only for
the lithium-ion batteries of the Power-X-Change
series!
Power-X-Change
•
18 V, 1.5 Ah, 5 lithium-ion cells
•
18 V, 2.0 Ah, 5 lithium-ion cells
•
18 V, 3.0 Ah, 10 lithium-ion cells
•
18 V, 4.0 Ah, 10 lithium-ion cells
•
18 V, 5.2 Ah, 10 lithium-ion cells
Power X-Change Plus
•
18 V, 2.6 Ah, 5 lithium-ion cells
•
18 V, 5.2 Ah, 10 lithium-ion cells
4. Operation (Fig. 1-3)
The battery charger can be used to charge either
1 or 2 rechargeable batteries. By charging inde-
pendently you can also charge diff erent batteries
(e.g.: 2.0 Ah and 4.0 Ah) simultaneously for the
charging times stated on the charger.
1. Pull the battery pack (a) out of the equipment,
pressing the pushlock button (b) to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(1) into the socket outlet. The green LEDs will
then begin to fl ash.
3. Insert the battery pack or packs (a) into the
battery charger (1).
4. In section 7 „Charger indicator" you will fi nd a
table with an explanation of the LED indicator
on the charger.
Anl_Power_X_Twincharger_3A_SPK9.indb 15
Anl_Power_X_Twincharger_3A_SPK9.indb 15
GB
If the battery fails to charge, please check
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts of the charging unit
If the battery still fails to charge, send
•
the charging unit
•
and the rechargeable battery
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Mounting the charging unit on a wall (Fig. 4)
The charging unit can also be mounted on a wall.
The correct dimensions for drilling holes in the
wall can be found on the back of the charging unit.
Spacing distances
≥ 10 cm from the wall (right + left)
≥ 100 cm from the ceiling
Caution!
When mounting on a wall you must use suitable
screws, e.g. 3.5 mm pan-head screws, in order to
prevent damage to the housing and risk of falling.
5. Cleaning and maintenance
Always pull out the power plug before starting any
cleaning work.
The equipment is not allowed to be stored in a
damp location or where there are caustic gases.
Keep it in a dry place out of the reach of children.
- 15 -
28.07.2021 07:31:07
28.07.2021 07:31:07
Advertenties
Inhoudsopgave
