Advertenties
Beschikbare talen
Beschikbare talen
Introduction
MANUFACTURER:
scheppach Fabrikation von
Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment and
success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due
to the non-compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113.
WE RECOMMEND:
Read through the complete text in the operating instruc-
tions before installing and commissioning the device.
The operating instructions are intended to help the user
to become familiar with the machine and take advan-
tage of its application possibilities in accordance with the
recommendations. The operating instructions contain
important information on how to operate the machine
safely, professionally and economically, how to avoid
danger, costly repairs, reduce downtimes and how to in-
crease reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in your
country. Keep the operating instructions package with
the machine at all times and store it in a plastic cover
to protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information. The machine can only be
operated by persons who were instructed concerning the
operation of the machine and who are informed about
the associated dangers. The minimum age requirement
must be complied with. In addition to the safety require-
ments in these operating instructions and your country's
applicable regulations, you should observe the generally
recognized technical rules concerning the operation of
woodworking machines.
Range of application
Your electronic mixing unit has been designed to blend
and stir the following materials:
- Thin liquid mixing material such as paints, varnishes
or plaster.
- Thick liquid mixing material such as adhesives, pas-
tes, filling compounds or mortar.
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
Unpacking
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the pack-
aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
Description of parts (Fig.1)
1. Mixing paddle (adapter)
2. Mixing paddle (includes mixer element)
3. Drive shaft
4. ON I OFF switch
5. Circuit breaker for ON/OFF switch
6. Speed controller
7. Handles
8. Motor
General safety standards
ATTENTION!
Please read the entire instructions. Failure to fol-
low the instructions below may result in causing
electric shock, fire and / or serious injuries.
Keep all safety information and instructions for fu-
ture reference.
In this safety information the term "power tool" refers
to mains operated power tools (with power cord) and
battery operated power tools (without power cord).
Workplace
• Keep your work area clean and tidy. Cluttered and
dark working areas are accident-prone.
• Do not operate power tools in explosive atmosphe-
res, where flammable liquids, gases or dust are pre-
sent. Power tools generate sparks which may ignite
the dust or fumes.
• Keep children and other persons away while opera-
ting a power tool. Distractions can be a reason for
losing control of the tool.
Electrical safety
• Power tool plugs must match the outlet. Do not
modify the plug in any way. Do not use any adap-
ter plugs with grounded devices. Unmodified plugs
and matching outlets will reduce the risk of electric
shock.
• Avoid physical contact with grounded surfaces such
as pipes, radiators, ranges and refrigerators. If your
body is grounded the risk of an electric shock incre-
ases.
• Do not expose the power tool to rain or wet condi-
tions. Water that enters a power tool will increase
the risk of electric shock.
• Do not abuse the cord; do not use the cord to carry
or hang up the power tool or to unplug the power
tool from the mains. Keep the power cord away from
heat, oil, sharp edges or the power tool's moving
parts. Damaged or tangled power cords will increase
the risk of electric shock.
11 І 108
Advertenties
