Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
14 | English
If you are not planning to use the air pump again soon, dis-
connect the power supply (15) from the mains.
Battery Charge Indicator
The battery charge indicator (d) in the display shows the
battery's state of charge:
Display
Capacity
75−100 %
50−75 %
25−50 %
5−25 %
0−5 %
Fitting/Changing the Adapter (see figure B)
Select the adapter best suited to the intended application:
– Valve adapter (2), e.g. for many bike valves.
– Ball needle adapter (3), e.g. for footballs.
– Volume adapter (4), for small beach items or sporting
goods, e.g. beach balls.
Slide the lid off the adapter storage compartment (1) and re-
move the adapter.
Screw the adapter fully into the pressure hose (9).
For standard car tyre valves (sometimes also used on bikes),
no adapter is required.
Operation
Starting Operation
Switching On and Off
To switch the air pump on or off, press the on/off
button (5). The last set target pressure is saved when
switching off the pump.
When no button on the air pump is pressed for approx.
3 minutes, the air pump automatically switches off to pre-
serve battery life.
Switching the worklight on and off
To switch the worklight (12) on and off, press the change
unit/worklight button (7) for approximately 1 second.
Do not look directly into the worklight; it can blind
u
you.
Changing the Unit of Measurement
For the pressure indicator, the units bar, psi and kPa are
available.
To change the unit of measurement, short press the change
unit/worklight button (7) as many times as needed until the
required unit of measurement appears in the unit of meas-
urement indicator (a).
Inflation
Fit the appropriate adapter to the pressure hose (9) if re-
quired. If present, remove the valve cap on the item to be in-
flated.
1 609 92A 83G | (04.07.2022)
Tighten the pressure hose (9) with or without the adapter on
or in the valve. The current pressure in the connected item
appears in the measured value indicator (b).
Inflation with Automatic Switch-off (AUTOSTOP):
– The last set pressure value appears in the target pressure
indicator (e). When using for the first time (factory set-
ting) or when the target pressure was previously deleted,
"−−" appears in the indicator.
– Setting or changing the target pressure: Press the reduce
target pressure button (6) or increase target pressure
button (10) as many times as needed until the required
value is set in the target pressure indicator (e). The value
will change more quickly if the buttons are pressed and
held.
– Press the pump button (11) to start the inflation process.
You can still change the target pressure during the infla-
tion process.
– The inflation process will stop automatically as soon as
the set target pressure is reached. The set target pressure
is saved when switching off the air pump.
Inflation without Automatic Switch-off (MANUAL):
– When inflating without automatic switch-off, there must
be no set target pressure ("−−" in the target pressure
indicator (e)). To delete a set target pressure, press and
hold the reduce target pressure button (6) until "−−" is
displayed.
– Press the pump button (11) to start the inflation process.
The current pressure in the connected item appears in
the measured value indicator (b).
– When the required pressure is reached in the measured
value indicator (b), press the pump button (11) again to
end the inflation process.
Errors – Causes and Corrective Measures
Cause
Corrective measures
Warning indicator (c) in the display and the air pump
switches off
The air pump is outside of
Allow the air pump to adjust
the permitted operating tem-
to the ambient temperature
perature range.
before you switch it on again.
Warning indicator (c) in the display during inflation
The electricity consumption
Check whether the air flow in
is too high.
the pressure hose or in other
parts is blocked.
Warning indicator (c) in the display when connected to
the power supply
Ambient temperature is out-
Allow the air pump to reach
side the permissible charging
the correct temperature. The
temperature range.
charging process begins
automatically as soon as the
permitted charging temper-
ature range has been
reached and the warning in-
dicator goes out.
"Er1" indicator in the display
Bosch Power Tools
Advertenties
Inhoudsopgave
