(13) Hose clamp
(14) USB cable
a)
(15) Power supply
(country-specific)
b)
(16) USB Type-C® port
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
b) USB Type-C® and USB-C® are trademarks of USB Implementers
Forum.
Display Elements
(a) Unit of measurement indicator
(b) Measured value indicator
(c) Warning indicator
(d) Battery charge indicator
(e) Target pressure indicator (PRESET)
Technical Data
Cordless air pump
Article number
Rated voltage
Max. output volume
Max. pressure
Weight according to
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
ure during operation and dur-
ing storage
Recommended power
A)
supply
Recommended USB cable
Rechargeable battery
Charging voltage
Max. charging current
Capacity
Energy
Number of battery cells
A) Additional technical data can be found at:
http://www.bosch-do-it.com/ecodesign
Noise/Vibration Information
Noise emission values determined according
to EN 62841‑1.
Typically, the A-weighted sound pressure level of the power
tool is 71 dB(A). Uncertainty K = 3 dB. The noise level when
Bosch Power Tools
working can exceed the volume stated. Wear hearing pro-
tection!
Vibration total values a
determined according to EN 62841‑1:
a
= 4 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
EasyPump
This may significantly reduce vibration and noise emissions
over the total working period.
3 603 J47 0..
Implement additional safety measures to protect the oper-
V=
3.6
ator from the effects of vibration, such as servicing the
l/min
10
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
bar
10.3
Assembly
psi
150
kPa
1030
Battery Charging (see figure A)
kg
0.43
u
°C
+10 to +40
Note: The battery is supplied partially charged. To ensure
°C
0 to +50
the maximum performance of the battery, use the power
supply to fully charge the battery before first use.
The lithium-ion battery can be charged at any time without
2 609 120 7..
reducing its service life. Interrupting the charging process
1 600 A01 6..
does not damage the battery.
The lithium-ion battery is protected against deep discharge
1 600 A01 6A8
by "Electronic Cell Protection (ECP)". A protective circuit
Li-ion
switches the air pump off when the battery is drained.
V
5
u
A
1
Ah
3.0
Wh
10.8
To charge the battery, connect the USB Type-C® port (16) to
1
the power supply (15) via the USB cable (14). Plug the
power supply into a plug socket.
The charging process will begin and will be indicated by con-
tinuously filling bars in the battery charge indicator (d). The
air pump cannot be used during charging.
When the charging process is complete, the battery charge
indicator (d) will be continuously lit until the air pump is dis-
connected from the power supply.
(triax vector sum) and uncertainty K
h
2
2
, K = 1.5 m/s
.
Use only the power supplies listed in the technical
data. Only these power supplies are matched to the lith-
ium-ion battery of your air pump.
Do not continue to press the on/off button after the
air pump has automatically switched itself off due to
an empty battery. This can damage the rechargeable
battery.
1 609 92A 83G | (04.07.2022)
English | 13