Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Anleitung_BT_BD_701_1625D_SPK7:_
GB
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
Load factor:
A load factor of S2 15 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (630/700 W) for no longer
than the time stipulated on the specifications label (15
minutes ON period). If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
Additional information for electric power tools
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
1. Damage to hearing if no suitable ear protection is
used.
6. Before starting the equipment
6.1. Installing the machine (Fig. 1/4/5)
Place the base plate (1) in the desired position.
Fasten the pillar (2) with flange using the supplied
screws (3).
Insert the screw gear in the drill table support.
Then insert the gear rack (30) in the drill table
support (5) with the teeth facing the screw gear
(identical projection).
Now slip these parts together over the pillar (2). In
doing so, make sure that the gear rack is correctly
seated in the teeth of the screw gear.
To secure the gear rack at the top end, slip on the
guide sleeve (29) over the pillar and fasten with
the screw.
You can now fit the table and clamp in place with
the clamping lever. Following this, fit the crank
(27) and fasten tightly with the screw (28).
16
18.05.2010
15:29 Uhr
Seite 16
Finally, fit the complete bit head to the pillar. Align
the head so that it is horizontal to the base plate
and fasten it in position with the screws (35).
Screw the 3 supplied handles (9) in the handle
mounts.
Before you mount the drill chuck with the MK
shank, check that both parts are clean. Insert the
taper mandrel in the taper of the drill chuck with a
powerful jolt. Then insert the taper in the spindle
(Fig. 13)
Check the tension of the V-belt regularly before
use (Fig. 9).
Note: All bare parts are greased in order to protect
them from corrosion. Before mounting the drill chuck
(10) onto the spindle (11), both parts must be
completely degreased using an environmentally
friendly solvent. This ensures optimal transmission of
power.
6.2. Installing the machine (Fig. 4/5)
Before you use the drill for the first time it must be
permanently fixed in position. Use both mounting
holes (12) in the base plate to do this. Ensure that the
equipment is freely accessible for operation,
adjustment and maintenance.
Note: The fixing screws may only be tightened to a
point where they do not distort or deform the base
plate. Excessive tension can lead to fracture.
6.3. Hinged chip guard (Fig. 6)
Unscrew the three screws (21). Push the transparent
cover (23) into the groove of the red mounting frame
(24) and fasten it again with the screws (21).
The height of the cover (23) is infinitely adjustable
and can be locked using both thumb screws (22).
The chip guard (13) can be flipped upwards to
change drill bits, however ensure that the chip guard
(13) is back in its initial position before restarting the
equipment.
6.4. Prior to using the machine for the first time
Ensure that the voltage of the mains supply complies
with the specifications on the rating plate. Connect
the equipment only to a socket with the properly
installed earthing contact. The drill is equipped with a
no-volt trip that is designed to protect the operator
from an undesired restart following a drop in voltage.
Should this happen, the equipment must be
physically restarted.
Advertenties
Inhoudsopgave
