Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Screw the struts to the front legs
and screws
. Tighten the nuts just enough so that the screw joints remain
13
flexible (see Fig. L and M).
Assemble the cross braces
8
Tighten the screws
(see Fig. N).
12
Use
Stand the workbench on its legs. Push the joints on the struts down until
they are horizontal and not bent. This gives the workbench stability and
it is ready to use (see Fig. O).
Note on functionality: Turning both crank handles simultaneously
will move the rear clamping plate
allows the size of the table surface to be adjusted. During use as a
clamping table, this allows the workpiece to be clamped (see Fig. P).
To clamp workpieces:
Insert the clamping jaws
in a suitable position in the clamping plates
1
,
, (see Fig. Q).
9
10
Clamping workpieces with parallel surfaces:
Turn the clamping jaws
so that their grooved surfaces hold the work-
1
piece (see Fig. R).
Clamping round workpieces:
Turn the clamping jaws
so that their horizontal indentations hold the
1
work piece (see Fig. S).
Use as a work table:
Remove the clamping jaws
1
a table surface of a suitable size (see Fig. T).
Care
Do not use harsh or abrasive cleaning agents. Allow the workbench to
dry fully before storing it.
Carefully clean the workbench after each use. To do this, use a brush or
a damp cloth.
Grease all moving parts occasionally using a standard lubricating grease.
Storage
Choose a dry location for storage.
Move the clamping plates
9
(see Fig. U).
Pull the joints of the struts upwards to bend them (see Fig. V).
Push the legs together at the bottom. The table surface will tilt upwards
(see Fig. W).
Push the legs
,
,
,
2
3
4
5
The workbench is ready for storage.
Store the workbench lying flat or leaning against a wall in such a way
that it cannot fall over.
Disposal
The packaging is made entirely of recyclable materials, which you may
dispose of at local recycling facilities.
Contact your local refuse disposal authority for more details of how to
dispose of your worn-out product.
6
GB/IE/NI
,
. To do this, use the washers, nuts
2
4
using the washers, nuts and screws
. During use as a work table, this
9
. Adjust the clamping plates
,
9
10
,
so that they are completely together
10
, together as far as they will go (see Fig. X).
Warranty
The product has been manufactured to strict quality guidelines and meticulously
.
examined before delivery. In the event of material or manufacturing defects
12
you have legal rights against the retailer of this product. Your legal rights are
not limited in any way by our warranty detailed below.
The warranty for this product is 3 years from the date of purchase. The war-
ranty period begins on the date of purchase. Keep the original sales receipt
in a safe location as this document is required as proof of purchase.
Any damage or defects already present at the time of purchase must be
reported without delay after unpacking the product.
Should the product show any fault in materials or manufacture within 3 years
from the date of purchase, we will repair or replace it – at our choice – free
of charge to you. The warranty period is not extended as a result of a claim
being granted. This also applies to replaced and repaired parts.
This warranty becomes void if the product has been damaged, or used or
maintained improperly.
The warranty covers material or manufacturing defects. This warranty does
not cover product parts subject to normal wear and tear, thus considered
consumables (e.g. batteries, rechargeable batteries, tubes, cartridges), nor
damage to fragile parts, e.g. switches or glass parts.
Service
to create
Conmetall Meister GmbH
Oberkamper Straße 39
42349 Wuppertal
GERMANY
Email: meister-service@conmetallmeister.de
Advertenties
Inhoudsopgave
