Inhoudsopgave
Advertenties
ENGLISH
10CH DMX-chart 10-C (DMX CHANNEL1 set between values 225 and 255)
CHANNEL
VALUE
CH 2
000-255
11 different standard patterns
000-127
Fixed pattern size: from big (100%) to small (5%)
CH 3
128-169
Zooming in (from big to small + from slow to fast)
ZOOMING
170-209
Zooming out (from small to big + from slow to fast)
210-255
Zooming in & out (from slow to fast)
000-127
0° to 359° fixed positions around Y axis
CH 4
Y AXIS
128-191
Clockwise rolling around Y axis
ROLLING
192-255
Anticlockwise rolling around Y axis
000-127
0° to 359° fixed positions around X axis
CH 5
X AXIS
128-191
Clockwise rolling around X axis
ROLLING
192-255
Anticlockwise rolling around X axis
000-127
0° to 359° fixed positions around Z axis
CH 6
Z AXIS
128-191
Clockwise rolling around Z axis
ROLLING
192-255
Anticlockwise rolling around Z axis
000-127
128 different fixed positions along the X axis
CH 7
128-191
Clockwise moving along the X axis
X AXIS MOVING
192-255
Anticlockwise moving along the X axis
000-127
128 different fixed positions along the Y axis
CH 8
128-191
Clockwise moving along the Y axis
Y AXIS MOVING
192-255
Anticlockwise moving along the Y axis
000-016
Original colors
017-031
RED
CH 9
032-047
GREEN
COLOR
048-062
RED + GREEN (YELLOW)
063-160
Changing between red and green (from slow to fast)
161-255
Changing mix of 3 colors (from slow to fast)
CH 10
NOT USED
MAINTENANCE
Make sure the area below the installation place is free from unwanted persons during servicing.
Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics.
Clean with a soft cloth using normal glass cleaning products.
Always dry the parts carefully.
Clean the external optics at least once every 30 days.
Clean the internal optics at least every 90 days.
JB SYSTEMS
®
USER MANUAL
DESCRIPTION
9/63
TWIN EFFECT LASER
ENGLISH
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
Mains Input:
AC 100~240V, 50/60Hz
Fuse:
250V 1.6A slow blow (20mm glass)
Total Power consumption:
28W
Sound Control:
Internal microphone
DMX connections:
3pin XLR male / female
DMX channels:
1 or 10 channels
DMX starting address:
001 512
Laser Power:
40mW Green CW laser (λ = 532nm)
80mW Red CW laser (λ = 650nm)
Laser radiation class:
3B
Beam diameter @ aperture:
<5mm
Divergence (each beam)
<2 mrad
Divergence (total output)
<160°
Working temperature:
15°C to 40°C
Laser Safety Standard:
EN/IEC 60825-1 Ed2, 2007-03
Size:
see picture below
Weight:
2,6kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
JB SYSTEMS
10/63
®
USER MANUAL
TWIN EFFECT LASER
Advertenties
Inhoudsopgave
