Download Inhoudsopgave Inhoud Print deze pagina

REID LIFTING PORTA-GANTRY 500 Montage- En Gebruiksaanwijzing pagina 9

Verberg thumbnails Zie ook voor PORTA-GANTRY 500:
Inhoudsopgave

Advertenties


4. Hanteer de spanratel om de gewenste hoogte instellen en zorg hierbij dat de boutgaten
op één lijn zitten.
5. Steek de bovenste bout erin om zo de staander vast te maken en plaats de ringen en moer.
6. Laat de spanband iets vieren en steek de tweede (onderste) bout erin en plaats ook hier
de ringen en de moer.
7. Controleer of alle bouten op de rijbrug goed zijn aangedraaid.
8. Indien het hijstoestel nog niet aan het bevestigingspunt van de trolley is bevestigd, is het nu
een goed moment dat te doen (met, indien nodig, het gebruik van een platformladder). Indien
dit niet veilig te doen is, moet u de rijbrug uit elkaar halen en hem opnieuw in elkaar zetten met
het hijstoestel bevestigd aan de trolley.
N.B. Zorg dat de balk horizontaal staat voordat enige hijswerkzaamheden worden uitgevoerd
– zie Methodeverklaring.


Tel: +44 (0) 1291 620796 enquiries@reidlifting.com
(Two Person Operation Recommended – one on each A-

Frame working concurrently).

1.
Decide on the height required (always use the lowest
setting for the work in hand).
2.
Remove lower bolt from behind the webbing strap.
3.
Tension the webbing strap slightly with the ratchet and
remove the upper bolt.
4.
Operate ratchet to adjust height to required setting,
ensuring that the bolt holes are aligned.
B) Instellen van de balkhoogte – A-Frame met Spanband Systeem:
5.
Insert upper bolt to retain the upright to the frame and
apply washers and nut.
Uitvoering met twee mensen wordt aangeraden – ieder gelijktijdig
(Two Person Operation Recommended – one on each A-
Frame working concurrently).
werkend aan een van de A-Frames.
6.
Release tension in ratchet strap and insert second
(lower) bolt, washers and nut.
1. Bepaal de gewenste hoogte (gebruik altijd de laagst mogelijke instelling
1.
Decide on the height required (always use the lowest
7.
Check all bolts on the gantry are secure.
setting for the work in hand).
voor de uit te voeren klus).
8.
If the hoist is not already attached to the suspension
2.
Remove lower bolt from behind the webbing strap.
point on the trolley, do so now (using platform ladder if
2. Verwijder de onderste bout, achter de spanband.
height setting requires). If this is not safe, disassemble
3.
Tension the webbing strap slightly with the ratchet and
gantry and reassemble the Gantry with the hoist
remove the upper bolt.
3. Zet lichte druk op de spanband met de spanratel en verwijder de
attached to trolley.
4.
Operate ratchet to adjust height to required setting,
bovenste bout.

ensuring that the bolt holes are aligned.

5.
Insert upper bolt to retain the upright to the frame and
apply washers and nut.

6.
Release tension in ratchet strap and insert second

(lower) bolt, washers and nut.
7.
Check all bolts on the gantry are secure.
8.
If the hoist is not already attached to the suspension
point on the trolley, do so now (using platform ladder if
height setting requires). If this is not safe, disassemble
gantry and reassemble the Gantry with the hoist
attached to trolley.





Ontgrendel de trolley- en wielremmen


om de PORTA-GANTRY direct boven het

liftpunt te positioneren.
(Two Person Operation Recommended – one on each A-
Frame working concurrently).
(Two Person Operation Recommended – one on each A-
Frame working concurrently).
1.
Decide on the height required (always use the lowest
setting for the work in hand).
1.
Decide on the height required (always use the lowest
setting for the work in hand).
2.
Remove lower bolt from behind the webbing strap.
2.
Remove lower bolt from behind the webbing strap.
3.
Tension the webbing strap slightly with the ratchet and
remove the upper bolt.
3.
Tension the webbing strap slightly with the ratchet and
remove the upper bolt.
4.
Operate ratchet to adjust height to required setting,
ensuring that the bolt holes are aligned.
4.
Operate ratchet to adjust height to required setting,
ensuring that the bolt holes are aligned.
5.
Insert upper bolt to retain the upright to the frame and
LICHTGEWICHT
DRAAGBAAR
VEILIG
8

Advertenties

Inhoudsopgave
loading

Inhoudsopgave