Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Screw the side grip on the tool securely.
Installing or removing abrasive disc
(Fig. 3)
Mount the pad onto the spindle. Fit the abrasive disc and
countersunk washer on the pad and screw the clamp
screw clockwise into the spindle.
To tighten the clamp screw, grip the edge of the pad with
your hand, then tighten the screw clockwise with a hex
wrench securely. (Fig. 4)
To remove the disc, follow the installation procedure in
reverse.
OPERATION
Sanding operation (Fig. 5)
CAUTION:
• Always wear safety goggles or a face shield during
operation.
• Never run the tool without the abrasive disc. You may
seriously damage the pad.
• Always use the side grip (auxiliary handle) and firmly
hold the tool by both side grip and switch handle during
operations.
Hold the tool firmly. Turn the tool on and then apply the
abrasive disc to the workpiece. In general, keep the
abrasive disc at an angle of about 15 degrees to the
workpiece surface. Apply slight pressure only. Excessive
pressure will result in poor performance and premature
wear to abrasive disc.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Plastic pad
• Abrasive discs
• Rubber pad (GV6010)
• Grip 36
All manuals and user guides at all-guides.com
NOTE:
• Some items in the list may be included in the tool
Noise
The typical A-weighted noise level determined according
to EN60745:
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
• The declared vibration emission value has been
• The declared vibration emission value may also be
• The vibration emission during actual use of the power
• Be sure to identify safety measures to protect the
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Disc Sander
Model No./ Type: GV5010, GV6010
are of series production and
Conforms to the following European Directives:
And are manufactured in accordance with the following
standards or standardised documents:
The technical documentation is kept by:
package as standard accessories. They may differ
from country to country.
Sound pressure level (L
pA
Sound power level (L
): 94 dB (A)
WA
Uncertainty (K): 3 dB (A)
Wear ear protection.
Work mode: disc sanding
Vibration emission (a
): 2.5 m/s
h,DS
2
Uncertainty (K): 1.5 m/s
measured in accordance with the standard test method
and may be used for comparing one tool with another.
used in a preliminary assessment of exposure.
WARNING:
tool can differ from the declared emission value
depending on the ways in which the tool is used.
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to
the trigger time).
2006/42/EC
EN60745
Makita International Europe Ltd.
Technical Department,
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
30. 1. 2009
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
ENG905-1
): 83 dB (A)
ENG900-1
2
or less
ENG901-1
ENH101-16
5
Advertenties
Inhoudsopgave
