Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
workpiece or of a broken accessory may fly away and
cause injury beyond immediate area of operation.
10. Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spinning
accessory.
11. Never lay the power tool down until the accessory
has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
12. Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
13. Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may
cause electrical hazards.
14. Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
15. Do not use accessories that require liquid
coolants. Using water or other liquid coolants may
result in electrocution or shock.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other
accessory. Pinching or snagging causes rapid stalling of
the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction
opposite of the accessory's rotation at the point of the
binding.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.
a) Maintain a firm grip on the power tool and
position your body and arm to allow you to resist
kickback forces. Always use auxiliary handle, if
provided, for maximum control over kickback or
torque reaction during start-up. The operator can
control torque reactions or kickback forces, if proper
precautions are taken.
b) Never place your hand near the rotating
accessory. Accessory may kickback over your hand.
c) Do not position your body in the area where
power tool will move if kickback occurs. Kickback
will propel the tool in direction opposite to the wheel's
movement at the point of snagging.
d) Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing have
a tendency to snag the rotating accessory and cause
loss of control or kickback.
e) Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create frequent
kickback and loss of control.
Safety Warnings Specific for Sanding Operations:
a) Do not use excessively oversized sanding disc
paper. Follow manufacturers recommendations,
when selecting sanding paper. Larger sanding
paper extending beyond the sanding pad presents a
laceration hazard and may cause snagging, tearing
of the disc or kickback.
4
All manuals and user guides at all-guides.com
Additional Safety Warnings:
16. Some material contains chemicals which may be
17. Ventilate your work area adequately when you
18. Use of this tool to sand some products, paints and
19. Make sure the abrasive disc is not contacting the
20. Do not leave the tool running. Operate the tool
21. Do not touch the workpiece immediately after
22. Check that the workpiece is properly supported.
23. If working place is extremely hot and humid, or
24. Do not use the tool on any materials containing
SAVE THESE INSTRUCTIONS.
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure to
follow the safety rules stated in this instruction
manual may cause serious personal injury.
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
Installing side grip (auxiliary handle)
(Fig. 2)
CAUTION:
• Always be sure that the side grip is installed securely
toxic. Take caution to prevent dust inhalation and
skin contact. Follow material supplier safety data.
perform sanding operations.
wood could expose user to dust containing
hazardous substances. Use appropriate
respiratory protection.
workpiece before the switch is turned on.
only when hand-held.
operation; it may be extremely hot and could burn
your skin.
badly polluted by conductive dust, use a short-
circuit breaker (30 mA) to assure operator safety.
asbestos.
WARNING:
unplugged before adjusting or checking function on the
tool.
the switch trigger actuates properly and returns to the
"OFF" position when released.
unplugged before carrying out any work on the tool.
before operation.
Advertenties
Inhoudsopgave
