Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
ENGLISH (Original instructions)
1.
Lock button
2.
Switch trigger
3.
Side grip
SPECIFICATIONS
Model
Abrasive disc diameter
Rated speed (n)/No load speed (n
Overall length
Net weight
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for the sanding of large surface of
wood, plastic and metal materials as well as painted
surfaces.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
DISC SANDER SAFETY
WARNINGS
Safety Warnings Common for Sanding Operation:
1. This power tool is intended to function as a
sander. Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious
injury.
2. Operations such as grinding, wire brushing,
polishing or cutting-off are not recommended to
be performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
3. Do not use accessories which are not specifically
designed and recommended by the tool
All manuals and user guides at all-guides.com
Explanation of general view
4.
Hex wrench
5.
Clamp screw
6.
Countersunk washer
)
0
ENE052-1
4. The rated speed of the accessory must be at least
ENF002-2
5. The outside diameter and the thickness of your
6. Threaded mounting of accessories must match
GEA010-1
7. Do not use a damaged accessory. Before each use
GEB036-5
8. Wear personal protective equipment. Depending
9. Keep bystanders a safe distance away from work
7.
Abrasive disc
8.
Plastic pad
9.
Spindle
GV5010
125 mm
4,500min
181 mm
1.2 kg
/II
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
the tool spindle thread. For accessories mounted
by flanges, the arbour hole of the accessory must
fit the locating diameter of the flange. Accessories
that do not match the mounting hardware of the power
tool will run out of balance, vibrate excessively and
may cause loss of control.
inspect the accessory such as backing pad for
cracks, tear or excess wear. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After inspecting
and installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum no-
load speed for one minute. Damaged accessories
will normally break apart during this test time.
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of
stopping flying debris generated by various
operations. The dust mask or respirator must be
capable of filtrating particles generated by your
operation. Prolonged exposure to high intensity noise
may cause hearing loss.
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
GV6010
150 mm
-1
3
Advertenties
Inhoudsopgave
