English
• Do not use vacuum without lters in place, except
as described under WET PICK UP APPLICATIONS.
• Some wood contains preservatives which can be
toxic. Take extra care to prevent inhalation and skin
contact when working with these materials. Request
and follow any safety information available from the
material supplier.
• Do not use vacuum as a step ladder.
• Do not place heavy objects on vacuum.
• An extension cord must have adequate wire size for
safety.
• If an extension cord is to be used outdoors it must
be marked.
WARNING:
To reduce the exposure to these chemicals, wear
approved safety equipment such as dust masks that
are specially designed to lter out microscopic particles.
ON MOTOR HOUSING :
WARNING:
• TO REDUCE THE RISK OF INJURY, USER MUST
READ INSTRUCTION MANUAL. DO NOT LEAVE
THE VACUUM UNATTENDED WHEN IT IS
SWITCHED ON. DO NOT PICK UP FLAMMABLE,
COMBUSTIBLE OR HOT MATERIALS. DO NOT
USE AROUND EXPLOSIVE DUST, LIQUIDS OR
VAPORS. ELECTRICAL DEVICES PRODUCE ARCS
OR SPARKS WHICH CAN CAUSE FIRE OR
EXPLOSION. DO NOT USE AT FILLING STATIONS
OR ANYWHERE GASOLINE IS STORED OR
DISPENSED. DO NOT VACUUM TOXIC OR
CARCINOGENIC MATERIALS OR OTHER HEALTH
ENDANGERING MATERIALS SUCH AS ASBESTOS
OR PESTICIDES. ALWAYS USE PROPER EYE AND
RESPIRATORY PROTECTION. TO REDUCE THE
RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE
TO RAIN. STORE INDOORS. WHEN SERVICING,
USE ONLY IDENTICAL REPLACEMENT PARTS.
NOT TO BE USED AS A STEP STOOL.
SAVE THESE INSTRUCTIONS
OPERATING INSTRUCTIONS
UNPACKING & SETUP SUMMARY
1. Pull lid latches in an outward motion, remove power
head and some accessories that may have been
shipped in the tank.
2. Attach heavy-duty rubberized casters following the
instructions in this manual.
3. Before replacing power head, refer to this manual to
ensure you have the proper lters installed for the
cleaning operation.
4. Replace power head, and apply pressure with thumb
to each latch until it snaps tightly in place. Make sure
all lid latches are clamped securely.
5. Insert the end of the hose into the inlet of the tank.
6. Attach the extension wands to the end of the hose.
Apply slight pressure until tting is tight.
7. Attach one of the cleaning accessories (depending
on the cleaning requirements) to the extension
wands. Twist slightly to tighten the connection.
8. Plug the cord into the wall outlet. The vacuum is
ready for use.
WARNING:
To reduce the risk of re or explosion, do not operate
this vac in areas with ammable gases, vapors or
explosive dust in the air. Flammable gases or vapors
include but are not limited to: lighter uid, solvent-type
cleaners, oil-based paints, gasoline, alcohol or aerosol
sprays. Explosive dusts include but are not limited to:
coal, magnesium, aluminum, and grain or gun powder.
Do not vacuum explosive dust, ammable or
combustible liquids or hot ashes. Do not use this vac
as a sprayer for any ammable or combustible liquid.
To reduce the risk of health hazards from vapors or
dusts, do not vacuum toxic materials.
WARNING:
SERVICING OF DOUBLE-
INSULATED WET/DRY VAC
In a double-insulated Wet/Dry Vac, two systems of
insulation are provided instead of grounding. No
grounding means is provided on a double-insulated
appliance, nor should a means for grounding be
added. Servicing a double-insulated Wet/Dry Vac
requires extreme care and knowledge of the system
Replacement parts for a double-insulated Wet/Dry
Vac must be identical to the parts they replace. This
double-insulated Wet/Dry Vac is marked with the words
"DOUBLE-INSULATED" and the symbol
within a square) may also be marked on the appliance.
To reduce the risk of injury from electrical shock, unplug
power cord before servicing the electrical parts of the
Wet/Dry Vac.
WARNING:
If the supply cord is damaged, it must be
replaced by the manufacturer or its service
to avoid a hazard.
WARNING:
Remove the plug from the socket before
performing maintenance. Before using the
machine make sure that the frequency and
voltage shown on the rating plate correspond
details are subject to change without prior
notice. The accessories shown in the
pictures may vary from model to model.
16
(square