Advertenties
GB
WARNING! Risk of injury from damaged
components. Damaged components of the pole-
mounted pruner can lead to serious injuries.
■
Before each use, check that the pole-mount-
ed pruner is complete and does not contain
damaged or worn components. Safety and
protective devices must be intact.
■
Inspect the tool in particular if it has been
dropped or has suffered a severe impact.
5.1
Filling saw chain oil (03)
There is no saw chain oil in the tool on deliv-
ery!
IMPORTANT! Danger of damage to the ap-
pliance. Use of the appliance without saw chain
oil leads to damage of the saw chain and the
guide rail.
■
Never operate the appliance without saw
chain oil.
■
Before starting work, fill the saw chain oil in
the oil tank and check the oil level during the
work.
■
At least before starting work each time, check
that the chain lubrication is working.
The service life and cutting performance of the
saw chain depend on optimum lubrication. The
saw chain has oil applied to it automatically
during operation.
IMPORTANT! Danger of damage to the ap-
pliance. Due to the metallic abrasion it contains,
the use of used oil for lubricating the chain would
lead to premature wear of the guide rail and saw
chain. Also, the warranty of the manufacturer will
become void.
■
Never use used oil, only biologically degrad-
able saw chain oil.
IMPORTANT! Danger of environmental dam-
age. The use of mineral oil for the chain lubrica-
tion leads to serious environmental damage.
■
Never use mineral oil, but only biologically
degradable saw chain oil.
Each time before starting work or changing the
rechargeable battery, check the oil level and re-
plenish the saw chain oil if necessary:
1. Check the oil level in the viewing aperture
(03/1) of the oil tank. It must always be possi-
ble to see oil. The minimum and the maxi-
mum oil level must not be exceeded.
2. Place and hold the pole-mounted pruner hori-
zontal on a firm surface.
34
3. Clean the tool around the oil tank cap (03/2).
4. Unscrew the oil tank cap.
NOTE
■
Use a funnel for easier filling.
■
Do not allow any dirt to get into the oil tank.
5. Fill the oil tank with biologically degradable
saw chain oil. While doing so, check the oil
level in the viewing aperture of the oil tank.
Do not allow it to overflow!
6. Screw down the oil tank cap again.
5.2
Charging the rechargeable battery
Observe the temperature range for charging, see
technical data.
NOTE For detailed information, see the sep-
arate operating instructions for the rechargeable
battery and the charger:
■
Operating manual 443130: Rechargeable
batteries
■
Operating manual 443131: Chargers
5.3
Inserting and removing the
rechargeable battery (04, 05)
IMPORTANT! Danger of damage to the re-
chargeable battery. If the rechargeable battery
is left in the appliance after use, it may damage
the rechargeable battery.
■
Immediately after use, pull the rechargeable
battery out of the appliance and store in a
frost-protected area.
■
Only insert the rechargeable battery in the
appliance immediately before starting work.
Inserting the rechargeable battery (04)
1. Push rechargeable battery (04/1) into battery
slot (04/2) of the basic tool until it engages
(04/a).
Removing the rechargeable battery (05)
1. Press and hold unlock button (05/1) on re-
chargeable battery (05/2).
2. Pull out the rechargeable battery (05/a).
6 OPERATION
6.1
Checking the charge status of the
rechargeable battery
Charge status indicator (01/6) is located on the
top of the basic appliance.
It has three segments. The segments light up or
flash, depending on the battery charge status.
Operation
CSA 1820
Advertenties
