Inhoudsopgave
Advertenties
❖ WARNING! CHARGE COMPLETELY BOTH OF THE DEVICES BEFORE FIRST TIME USE!
1.ON/ OFF button: Press and hold the button for about 2 seconds to turn on the sender and the receiver. The indicating
light will flash in green colour showing that the devices are turned on. They should be away from each other in order to
avoid interference in the signal.
2.Place the sender in the room of the baby. Point the microphone towards the child, e.g. to the baby bed or play area. It
should be at least 1 to 2 meters away from the child.
If you have plugged the charger into the sender and mains outlet, fully extend the cable to achieve the best possible
transmission. Plug the adapter into the nearest standard electrical outlet in your home.
3.Pairing the devices to each other: the devices should be paired in the factory. If the parent unit doesn't receive any
signal from the baby unit:
-Check if both of the devices are completely charged. If they are not, charge them.
-If after charging the units cannot be paired again, hold the on/ off button of the receiver (parent unit) for approximately
5 seconds until the LED indicator starts flashing. Then hold the on/ off button of the sender (baby unit) for approximately
5 seconds. This way the units will pair to each other.
4.The sender will switch to stand-by mode to save energy if it does not detect sounds in the surrounding area (VOX
mode). It will turn on automatically if there are sounds in the baby room.
5.Place the receiver in the room you are in.
6.Press the▲ and ▼ buttons on the parent unit to control the sound volume. Press and hold the ▲ button for a few
seconds on the parent unit to turn on the light indicator. If there is sound transmitted from the sender to the receiver the
light indicator will flash.
7.Press the button ▲ with light on the sender to turn on the night light. Press the ▼ button with smaller lamp and a soft
flashing light will turn on.
8.The appliance is with the two-way communication function. Press and hold the volume down button and start talking to
the mic of the parent unit. This way your child can hear you. And with this function you can calm down the child remotely
until you reach the baby room.
9.If the battery of the baby or parent unit is exhausted, the power light indicator will flash in green. In this case, charge
the units as described in the manual.
10.Background noise: The echo noise from the receiver means that the batteries are exhausted and should be charged.
Check if the GREEN light indicator for the charging is flashing, this means the units should be charged.
11.If the parent unit is out of range, meaning the receiver is far away from the sender, then both of them cannot work
properly. The night light on the baby unit (sender) the indicating lights will flash slowly and the voice indicating light will
also flash. In the same time alarm (beep beep) will sound from the parent unit.
12.Echo: The receiver is too close to the sender, and there may be some echo. In this case place both of the units away
from each other or turn down the volume on the receiver.
13.Voice indication from the baby unit: If you press and hold the Vol+ button on the parent unit, the voice indication
function from the baby unit will be activated. Whenever there is sound from the baby unit, the voice indicating light will
start flashing (the upper circle in white light). The speed of flashing depends from the speed of the sound coming from the
sender. If the flashing of the white light is fast, this means the frequency of the baby cry is too high.
INDICATING LIGHTS
1. Sender (baby unit):
•LED indicator of the signal – the bottom light indicator: When the baby unit is connected to the parent unit, there will be
green light. When pairing the units – flashing green light (when pressing and holding the power button for 5 seconds).
•Power/ charging light indicator – the upper light indicator: When the power is on, there will be green light. When
switching the unit off, the green light is off. Low battery – flashing green light. Charging – red light is on. When the unit is
fully charged, the red light will turn off.
2. Receiver (parent unit):
•LED indicator of the signal – the bottom light indicator: When the parent unit is connected to the baby unit, there will be
green light. When pairing the units – flashing green light (when pressing and holding the power button for 5 seconds).
•Power/ charging light indicator – the upper light indicator: When the power is on, there will be green light. When
switching the unit off, the green light is off. Low battery – flashing green light. Charging – red light is on. When the unit is
fully charged, the red light will turn off.
CLEANING AND MAINTENANCE
1. Do not immerse the units or their adapters into water and do not wash under running water.
2. Do not use cleansing spray and liquid cleansers.
3. Before cleaning the units, you have to unplug the supply cord from the mains outlet.
4. Clean the units with soft dry cloth.
12
Advertenties
Inhoudsopgave
