Inhoudsopgave
Advertenties
ADAPTOR AND CHARGING THE BUILT-IN BATTERIES OF THE DEVICES
1.Before first use charge the batteries of the baby unit and mother unit completely.
2.The chargers are with the following specifications: Input: 100V – 240V- 50/60Hz; Output: 5V 1A 5.0W. The
AC chargers are with low voltage.
3.Charging:
-Connect the charger to the designated charging jack.
-Connect the charger's plug into electrical outlet of the mains supply of your home. The plug is used to connect the device
to the power supply, the device must be easily accessible.
-We recommend you to leave the devices to charge completely before next use to in order to prolong their battery life.
❖ WARNING: The provided charger is with special design suitable for this product. It cannot be used for other appliances.
You should not use other types of chargers for this baby monitor, which are not provided by the manufacturer/ importer.
4.Charge the appliances immediately after the light indicator starts flashing in green.
5.If you will not use the product for a long time, charge the batteries of both of the units completely before storing them.
Then charge the batteries at least once a month to prolong its life.
6.The built-in batteries cannot be taken out of the product.
7.If the batteries are damaged or cannot be charged anymore, do not try to open the appliance. For consultation and
repair contact the shop from which you bought the product or the importer/ distributor.
8.The batteries are recyclable. If the product is damaged and cannot be used any longer, take it to an official collection
point for electronic products' waste, batteries, chargers. DO NOT throw the product away with the household waste.
Follow your country's rules for the separate collection of electrical and electronic products and rechargeable batteries.
Dispose of waste of this type only at the designated places. This will be important and significant contribution for the
environmental protection and the reduction of the harmful effects of the substances contained in batteries and electronic
components on the environment and human health.
❖ WARNING! CHARGE COMPLETELY BOTH OF THE DEVICES BEFORE FIRST TIME USE!
1.ON/ OFF button: Press and hold the button for about 2 seconds to turn on the sender and the receiver. The indicating
light will flash in green colour showing that the devices are turned on. They should be away from each other in order to
avoid interference in the signal.
2.Place the sender in the room of the baby. Point the microphone towards the child, e.g. to the baby bed or play area. It
should be at least 1 to 2 meters away from the child.
If you have plugged the charger into the sender and mains outlet, fully extend the cable to achieve the best possible
transmission. Plug the adapter into the nearest standard electrical outlet in your home.
3.Pairing the devices to each other: the devices should be paired in the factory. If the parent unit doesn't receive any
signal from the baby unit:
-Check if both of the devices are completely charged. If they are not, charge them.
-If after charging the units cannot be paired again, hold the on/ off button of the receiver (parent unit) for approximately
5 seconds until the LED indicator starts flashing. Then hold the on/ off button of the sender (baby unit) for approximately
5 seconds. This way the units will pair to each other.
4.The sender will switch to stand-by mode to save energy if it does not detect sounds in the surrounding area (VOX
mode). It will turn on automatically if there are sounds in the baby room.
5.Place the receiver in the room you are in.
6.Press the▲ and ▼ buttons on the parent unit to control the sound volume. Press and hold the ▲ button for a few
seconds on the parent unit to turn on the light indicator. If there is sound transmitted from the sender to the receiver the
light indicator will flash.
7. Press the button ▲ with light on the sender to turn on the night light. Press the ▼ button with smaller lamp and a soft
flashing light will turn on.
8. The appliance is with the two-way communication function. Press and hold the volume down button and start talking
to the mic of the parent unit. This way your child can hear you. And with this function you can calm down the child
remotely until you reach the baby room.
9. If the battery of the baby or parent unit is exhausted, the power light indicator will flash in green. In this case, charge
the units as described in the manual.
10. Background noise: The echo noise from the receiver means that the batteries are exhausted and should be charged.
Check if the GREEN light indicator for the charging is flashing, this means the units should be charged.
11.If the parent unit is out of range, meaning the receiver is far away from the sender, then both of them cannot work
properly. The night light on the baby unit (sender) the indicating lights will flash slowly and the voice indicating light will
also flash. In the same time alarm (beep beep) will sound from the parent unit.
USE OF THE PRODUCT
11
Advertenties
Inhoudsopgave
