Advertenties
EN
Keep this instruction manual for future reference.
INTRODUCTION
Anyone using, cleaning or disposing of this product must be fa-
miliar with the instructions in this manual.
These operating instructions are an integral part of the product.
PURPOSE AND USE
This unit is designed to be used as a FLEXIBLE HOSE REEL for
COMPRESSED AIR, any other use is considered improper. The
manufacturer declines all responsibility for damage or accidents
resulting from improper use of the unit or from failure to comply
with the safety regulations. Any tampering or modification of the
unit not previously authorized relieves the manufacturer from
damages deriving from or referable to the above-mentioned acts.
PACKAGE CONTENTS
● Reel with fixing bracket
● Quick coupling
● Connector (nipple)
● Expansion plugs (2), washers (2), nuts (2)
DESCRIPTION OF THE UNIT (Fig. 1)
1. Fixing bracket for wall mounting
2. Reel
3. Hose stop
4. Hose
5. Quick coupling
6. Quick coupling (nipple)
7. Connecting hose (air inlet)
SAFETY WARNINGS
● DO NEVER exceed the stated maximum operating pressures.
● ALWAYS discharge the air pressure before carrying out the
fixing (on the wall), cleaning or reassembly of the unit.
● The reel must be fixed to a stable wall, capable of supporting
both weight and load.
● Take care of the hose, preventing it from becoming trapped
between obstacles and/or surrounding objects.
● Protect the hose from oil, acids, sharp edges and high tem-
peratures.
● At the end of each use, rewind the hose completely, putting it in
its housing; this way the reel will be protected of unnecessary
and prolonged tension.
Warning!
In the event that the hose (4) is damaged, do not use the unit
and dispose of it in accordance with current regulations.
INSTALLATION
After removing the unit from the packaging and checking its in-
tegrity, make sure that all the components listed in the "package
contents" are present inside the packaging.
Ensure that it is possible to install the reel sufficiently close to the
compressed air source so that the connecting hose (7) can be
easily connected to the source.
● Use a pencil to mark the points where holes are to be drilled
for fastening (Fig. 2).
6
● Drill two holes in the wall (fig. 3) with the same diameter as
the plugs supplied.
● Drive the anchors of the expansion plugs into the holes in
the wall (Fig. 4).
● Put the retaining bracket (1) at the threads of the dowels, then
hang the unit, taking care to thread the slots of the reel bracket
over the threads.
● Gently let the reel downwards, so that both threads fit into
the narrow slot.
● Mount one washer and one nut on each thread and tighten
the nuts.
Warning!
Ensure that the fixing bracket (1) is securely fixed to the
wall.
USE
Warning!
Ensure that the compressed air system is not under
pressure when connecting the unit.
● Connect the quick coupling (6) of the connecting hose (7) to
the outlet of the compressed air source.
● Grasp the hose retainer (3).
● Pull the hose (4) and pull it out as far as necessary, holding it
firmly. The rewind mechanism is locked (like a rolling shutter),
so the hose does not return automatically unless it is pulled out
again. For each metre of hose there are 2-3 clamping points.
Do not pull the hose out beyond the safety mark stamped
on the hose.
● At the end of use, switch off the compressed air source and
release the pressure. Gently pull the hose (4) and let the
mechanism rewind it.
● Accompany the hose (4) during rewinding. Ensure that the hose
does not twist or snag while being rewound.
● The hose must not be under pressure when being rewound
or during use.
CLEANING
● Clean the reel with a well-wrung cloth or brush. Do not use ag-
gressive or abrasive cleaning agents, as these could damage
the hose (4) and the hose reel (2).
● Avoid spraying water on or inside the reel.
● Keep the reel hose clean to allow proper sliding.
Advertenties
