Inhoudsopgave
Advertenties
User manual
Translation of the original
instructions
INSTALLATION AND INSPECTION CHECKS
REGULAR INSPECTION:
- Check that the screws are correctly tightened as described in the «assembly» section.
- Check that the foam gasket and pads are correctly positioned and undamaged.
- Check that the cord is correctly wound on the winch, and that it is not damaged.
If in doubt and/or if a defect is found, do not use the machine and contact the distributor or the manufacturer via the
After Sales Service.
INSTALLATION:
To ensure maximum adhesion to the floor, it is essential to position the Airfix Draw Aligner in a clean area (free of dust
liquids or other contaminants) with no cracks or joints between the tiles to ensure maximum vacuum performance.
The Airfix Draw Aligner is fitted with two rear wheels, tilt the column taking care not to damage the seal which is
located on the underside of the plate.
The Airfix Draw Aligner works with compressed air, the recommended pressure is between 5 and 8 bar.
USAGE:
- Move the pillar by tilting it backwards to the chosen work area.
- Position the Airfix Draw Aligner at an appropriate pulling distance, judged by the operator, as close as possible to the
point being repaired.
- Connect the compressed air hose. Check that the Airfix Draw Aligner is firmly anchored to the ground by pushing it
firmly.
14
AIRFIX DRAW ALIGNER
Screw M12x85: 1
Washer M12: 2
Nut M12: 1
Screw the pulley to the bracket using two 19mm
spanners.
Screw M6x18 : 1
Screw M6x25 : 2
Nut M6 : 3
Fix the winch to its support using the reinforcement plate,
the support plate and the 3 bolts. Use a BTR H5 spanner.
Place the trolley with the winch on the column.
User manual
Translation of the original
instructions
If the column does not stay in position, check the placement of the seal and the condition of the floor,
and repeat the previous operation.
Adjust the winch position to the desired working level. To do this:
- Raise the safety pin at the rear of the winch stand, and tilt the front of the mount upwards.
- Lower or raise the winch while keeping the safety pin raised and the bracket tilted to the desired working po-
sition. Please ensure that the notch is correctly located in the opening in the column.
Make sure that the column is correctly aligned with the panel being straightened.
- The pulling force produced by the winch is 350Kg and is delivered by a mechanical system with an auto-
matic load brake.
- To release the tension, simply turn the crank in the other direction. To make a downward pull, use the
pulley on the front of the Airfix and pass the cable underneath.
Always keep a minimum of 3 wraps around the winch spool.
MAINTENANCE
Dust removal can be done with a compressed air blow gun before cleaning. Clean the Airfix Draw Aligner with a
suitable cleaning product for painted steel surfaces. Follow the product's cleaning instructions. Wipe the Airfix Draw
Aligner with a cloth after cleaning. Never use a high-pressure washer, as this will damage the paint.
WARRANTY
The warranty covers any defects or manufacturing faults for two years, from the date of purchase (parts and labour).
The warranty excludes incidents due to misuse, dropping, dismantling, or any other damage due to transport. The
warranty does not cover normal wear and tear of parts if maintenance is not kept up to date. Only spare parts from the
manufacturer may be used for repairs.
DEFECTS, CAUSES, SOLUTIONS
TROUBLESHOOTING
Fitting not properly connected.
When connected to the compressed air
network, no noise is
produced.
No air in the network.
Poorly positioned seal.
Venturi not properly attached to the
plate.
The Airfix Draw Aligner does not stick to the
Worn joint.
floor.
Floor condition.
Clogged muffler
AIRFIX DRAW ALIGNER
CAUSES
Solutions
Connect your compressed air fitting
firmly to the Airfix Draw Align
Check that your compressed air system
is working properly (valve closed)
Reposition the seal correctly in the
groove by placing it end to end (see
marking on the plate)
Tighten the two visible screws on the un-
derside of the plate with an H5 spanner.
Change the seal with a new one (contact
your distributor)
Position on a clean, non-porous floor
with no major imperfections.
Unscrew the silencer and blow it out. If
too dirty, change it. To access the silen-
cer, carry out step two in reverse order
15
Advertenties
Inhoudsopgave
