Inhoudsopgave
Advertenties
EnGLIsh
To Install the Battery Pack into the Dust Extractor
1. Align the battery pack
1
extractor (Fig. B).
2. Slide the battery pack in until it is firmly seated in the dust
extractor and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the
Dust Extractor
1. Press the release button
out of the dust extractor.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D
WALT battery packs include a fuel gauge which
E
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button
. A combination of the three green LED lights will
14
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Attaching the Carry Strap (Fig. C)
Your dust extraction system comes with a carry strap
be connected to the carry strap hooks
shown in Fig. C.
Attaching the Crevice Tool (Fig. A)
•
To attach the crevice tool
insert the end of the dust extractor hose into the open end
of the accessory with a twisting motion until tight.
nOTE: The dust extraction hose is not compatible with
AirLock® connectors.
•
To remove the crevice tool, hold the dust extraction hose
and pull the accessory off using a twisting motion.
Installing the Belt Hook (Fig. K)
WARNING: To reduce the risk of serious personal
injury, turn the dust extractor off and disconnect
battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the dust
extractor from a work belt. DO NOT use the belt hook
for tethering or securing the dust extractor to a person
or object during use. DO NOT suspend dust extractor
overhead or suspend objects from the belt hook.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
34
with the rails inside the dust
2
and firmly pull the battery pack
10
in either manner as
11
12
to the dust extractor hose
IMPORTanT: When attaching or replacing the belt hook
only the screw
the screw.
If the hook is not desired at all, it can be removed from the
dust extractor.
Attaching the Suction Cup to the
Dust Extractor (Fig. E)
WARNING: Use this attachment only with D
recommended dust extractors. For more information
about D
attachment, please contact your local dealer or visit
www.dewalt.com.
Push dust extractor hose
until tight.
Attaching the Suction Cup to a Vertical or
Horizontal Surface (Fig. F, G)
The suction cup
horizontal surface.
1. With the suction cup securely connected to the dust
extractor, turn the dust extractor on.
2. Place the suction cup onto the floor or wall and press firmly
to engage the cup to the surface.
Removing the Suction Cup from a Surface
WARNING: DO NOT turn off the dust extractor before
that can
removing the suction cup from the surface as instructed.
Turning off the dust extractor before removing the suction
cup will result in the suction cup falling from the surface
which could cause injury.
To remove the suction cup
6
,
attached, pry the lip away using your hand. Do not remove by
pulling on the hose.
Replacing the Button Cell Battery in the
optional Remote Control N547456 (Fig. L)
WARNING: KEEP NEW AND USED BATTERIES AWAY FROM
CHILDREN. If the battery compartment does not close securely,
stop using the product and keep it away from children. If you
think batteries might have been swallowed or placed inside any
part of the body, seek immediate medical attention.
WARNING: WHEN REPLACING BATTERY, REPLACE IT
WITH THE SAME OR EQUIVALENT TYPE CR2032. Observe
correct polarity (+ and –) when replacing batteries. Do not
store or carry batteries so that metal objects can contact
exposed battery terminals.
WARNING: ENSURE THAT COIN CELL REPLACEMENT IS
CARRIED OUT PROPERLY. There is a risk of explosion.
that is provided. Be sure to securely tighten
16
WALT dust extractors compatible with this
E
6
into the connection point
can be fixed into place on a vertical or
13
from the surface to which it is
13
DANGER: DO NOT INGEST BATTERY;
CHEMICAL BURN HAZARD.This product contains
a coin / button cell battery. If the coin / button cell
battery is swallowed, it can cause severe internal
burns in just 2 hours and can lead to death.
20
, use
WALT
E
15
Advertenties
Inhoudsopgave
