Advertenties
Functions
,
,
Once installed, the sensor can be put into operation. Control
dials are provided on the sensor unit for selecting time, twi-
light and programme settings. After pressing the engagement
Switch-off delay
(time setting)
(factory setting: 5 sec.)
5 sec. – 15 min.
Twilight setting
(sensor response threshold)
(factory setting: daylight operation 2000 lux)
2 - 2000 lux
Programme setting
(factory setting: programme 1)
The following programmes only relate to
the LED corona of light and the Power LED
effect light. Once ambient light levels reach
the twilight setting, the main light always
switches "ON" in response to movement
and "OFF" again after the selected time
setting.
* Note on LED comfort economy programme
3
:
The sensor does not have any integrated clock. The middle of
the night is only determined on the basis of the length of dark-
ness phases. To work perfectly, therefore, it is important for
the light to be permanently connected to the power supply
during this period. During the first night (calibration phase) the
LEDs remain activated. Values remain saved even in the event
of mains power failure.
lug
with a flat-bladed screwdriver, the sensor unit can be
removed for ease of setting. In this case, the SensorLight
automatically switches to constant output.
Light "ON" duration can infinitely varied from 5 sec. to 15 min.
Control dial set to – = shortest time (5 sec.)
Control dial set to + = longest time (15 min.)
When setting the detection zone, it is recommended to select
the shortest time –.
The sensor's response threshold can be infinitely varied from
2 – 2000 lux.
Control dial set to
= daylight operation at approx. 2000 lux.
Control dial set to
= night-time operation at approx. 2 lux.
To adjust the detection zone in daylight, the control dial must be
set to
(daylight operation).
Programme
1
+
2
: LED comfort programme:
l
LEDs "ON" from twilight setting for the whole night.
3
Programme
: LED comfort economy programme*:
l
LEDs "ON" from twilight setting to the middle of the night.
l
The LEDs then switch "ON" in response to movement.
4
Programme
: LED standard programme:
l
LEDs switch "ON" in response to movement.
l
LEDs go out when time setting elapses.
We recommend not to interrupt the power supply in pro-
gramme
3
. As the values are determined over several nights,
the sensor should, in the event of any fault, be observed over
several nights to ascertain whether the LED switch-off time
moves towards the middle of the night.
- 10 -
Adjusting the detection zone
The detection zone can be limited to suit requirements. The
shrouds supplied with the light can be used to mask out as
many lens segments as you wish.This prevents the light from
being activated unintentionally, e.g. by cars, passers-by etc.
Manual override function
If a mains switch is installed in the mains supply lead, the light
is capable of the following functions in addition to the simple
"ON"/"OFF" function:
Sensor mode
1) Switch light "ON" (when light is "OFF"):
Turn switch "OFF" and "ON" once.
Light stays "OFF" for the period selected.
2) Switch light "OFF" (when light is "ON"):
Turn switch "OFF" and "ON" once.
The light goes out or switches to sensor mode.
Technical specifications
Dimensions (W x H x D):
295 x 72 x 105
Power supply:
230 – 240 V/50 Hz
Output:
12 W LED effect light and LED Power light, approx. 1 W
low-energy bulb only with max. Ø of 48 mm / 15 W max.
Angle of coverage:
360° with 90° angle of aperture and sneak-by guard
Sensor reach:
8 m max. all round
Time setting:
5 sec. – 15 min.
Twilight setting:
2 – 2000 lux
Programme setting:
4 programmes geared to practical needs (see above)
Manual override:
selectable (4 hrs.)
Condition: switch in mains power supply lead
Temperature range:
-10 °C to +50 °C
IP rating:
IP 44
Protection class:
II
Technical specifications for the enclosed LED lamp
Output:
8.5 W / E27
Luminous flux/efficiency:
674 lm / 79.3 lm/W
Colour-rendering index:
RA ≥ 80
Colour temperature:
3000 K (warm white)
LED life expectancy:
25,000 hours
Operation/Maintenance
The SensorLight is suitable for switching light "OFF" automati-
cally. Weather conditions may affect the way the SensorLight
functions. Strong gusts of wind, snow, rain or hail may cause
the light to come "ON" when it is not wanted because the
sensor is unable to distinguish sudden changes of temperature
Declaration of conformity
This product complies with
- Low Voltage Directive 2006/95/EC
- EMC Directive 2004/108/EC
and allows you to target danger spots. The shrouds and
shroud foils can be divided along the grooves. They can then
simply be pushed or stuck onto the lens.
Manual override
1) Activate manual override:
Switch 2 x "OFF" and "ON". The light will stay on for 4 hours
(red LED lights up behind the lens).
Then it returns automatically to sensor mode (red LED off).
2) Deactivate manual override:
Turn switch "OFF" and "ON" once. The light goes out or
switches to sensor mode.
Important:
The switch should be actuated in rapid succession
(in the 0.5 – 1 sec. range).
from sources of heat. The detector lens may be cleaned with
a damp cloth if it gets dirty (do not use cleaning agents). The
mini-sensor unit
can be removed for cleaning the LED
corona
.
- RoHS Directive 2011/65/EC
- WEEE Directive 2012/19/EC
- 11 -
Advertenties
