Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Mount, Use & Dismount
Transportation of Equipment:
There are two rollers equipped on the front foot. For moving, you can lift
up the rear foot and drive it to where you would like to locate or store it.
(Attention: If this item hasn't got a fixed handlebar, please use carefully the
left and right arms for procedure.)
Mount, Use & Dismount
Mount:
a.
Stand beside the item, put the nearest footrest into deepest position
and hold the fixed handlebar tightly.
Training area in mm
(for home trainer and user)
Cleaning, Checks and Storage of the Ergometer
bike:
1. Cleaning
Use only a less wet cloth for cleaning. Caution: Never use benzene,
thinner or other aggressive cleaning agents for surface cleaning as
this damage caused.
The device is only for private home use and for use suitable indoors.
Keep the unit clean and moisture from the device.
2. Storage
Plug out the power supply unit while intending the unit for more than
4 weeks not to use. Choose a dry storage in-house and put some
spray oil at front & rear foot tube connection point and hand grip
axle. Cover the bike to protect it from being discolor by any sunlight
and dirty through dust.
3. Checks
We recommend every 50 hours to review the screw connections for
tightness, which were prepared in the assembly. Every 100 operating
hours, you should put some spray oil at front & rear foot tube con-
nection point and hand grip axle.
b.
Put your foot onto the footrest, try to put whole body weight on your
foot and simultaneously cross over
with your another foot on the other side footrest and place there on
the footrest too.
c.
Now you are in the position to start your training.
Use:
a.
Keep your hands in desired position on the fixed handlebar.
b.
Pedal your exercise item by step your feet on footrests and balance
the body weight to left and right side of footrest
c.
If you like to exercise the upper body too, you can place the hands
from fixed handle bar to the left and right handle grips.
d.
Then you can increase the pedaling speed gradually and adjust braking
resistance levels to increase the exercise intension.
e.
Keep always your hands on fixed handle bar or hand grips left and
right.
Dismount:
a.
Slow down the pedaling speed until it comes to rest.
b.
Keep the hands grabbing the fixed handlebar tightly, put one foot cross
over the equipment and land on the floor, then
land the other one.
This training equipment is a stationary exercise machine used to simulate
a combination of biking, stepping and walking without
causing excessive pressure to the joints, hence decreasing the risk of
impact injuries.
Exercise this item offer a non-impact cardiovascular workout that can vary
from light to high intensity based on the resistance preference set by the
user. It will strengthen your muscles of upper and lower body and increase
cardio capacity and maintain fitness of your body also.
Free area in mm
(Training area and security area
(rotating 60cm))
Troubleshooting
If you cannot solve the problem with the following information,
please contact the authorized service center.
Problem
Possible Cause
Computer has
No power
no value at Dis-
adapter is well
play if you press
plugged or wall
any key.
power is without
power.
Computer is
Sensor impulse
not counting
missing base on
data and do not
not well plugged
switch on after
connection
start cycling.
Computer is
Sensor impulse
not counting
missing base on
data and do not
not correct posi-
switch on after
tion of sensor.
start cycling.
No pulse value
Pulse cable is
not plugged in.
No pulse value
Pulse sensors
not well connec-
ted
24
Solution
Check that the power adapter
is properly plugged in, possibly
with another electric device
check if the wall power is fine.
Check the plug connections at
computer and inside of handle-
bar support.
Take off the cover and check
the distance between magnet
and Sensor. The magnet at
turning belt wheel should have
only less than < 5mm distance
against the sensor position.
Check the separately pulse
cable is well connected with
computer. Check the connec-
tions of the pulse cable.
Screw out the screw for pulse
measurement and check if
plugs are well connected and no
damage at pulse cable.
Advertenties
Inhoudsopgave
