Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
GB
IMPORTANT SAFETY NOTES
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by "one person only".
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
<< Danger of injury! Keep all loose
articles of clothing, ties, jewe-
lery, long hair or other loose
objects away from opening!
CONTROLS:
1 = Mains plug (fig. 2)
When the machine is first plugged in it is
not on.
2 = Function buttons (fig. 1)
"Ready"/ "Off" / "Stop"
This button has three functions:
a) "Ready"
The machine changes to "Ready" if you
press this button briefly.
At the same time the integral LED
display
comes on.
b) "Off"
The machine switches off if it is in the
"Ready" mode and the button is held
down for about 3 seconds.
Note:
The
machine
automatically if it is not used for about 5
minutes.
c) "Stop"
If you press this button briefly when the
cutters are running they switch off and
stop.
6
7
8
2
fig. 1
<< Danger of injury! Never insert fingers into
<< In case of danger switch the machine off
<< Always unplug the machine from the mains
Special materials
Symbol
Model
120SP2 (SC2)-3,8
120SP2 (SC2)-5,8
120CP4 (CC3)
120CP5 (CC4)
120CP6 (CC5)
120CP7 (CC6)
3 = Forwards button (fig. 1)
This button has two functions:
a) If this button is pressed briefly, the
cutting mechanism runs forwards for a
few seconds, e.g. to remove remaining
material from the cutting mechanism.
At the same time the integrated LED
display
b) If this button is pressed and held
for approx. two secs., the cutting
mechanism runs forwards continually
and materials to be shredded can be fed
into the machine. At the same time the
integrated LED display
4 = Reverse button (fig. 1)
If you press this button the cutters run
switches
off
backwards for a short time. At the same
time the integral LED display
5 = Light barrier (Forward motion) (fig. 3)
The shredding procedure starts as soon
as material is fed into the feed slot. At the
same time the integral forward button LED
display
3
9
10
1
4
120 SP2(SC2)/CP4(CC3)/CP5(CC4)/CP6(CC5)/CP7(CC6)
opening!
with the mains switch, or with the emer-
gency switch, or unplug the machine!
power supply before opening the machine!
Repairs may only be performed by trained
personnel!
X
X
X
X
X
X
X
X
X
X
X
X = not applicable for shredding
OPERATION
lights up.
lights up.
comes on.
comes on.
fig. 2
5
INITIATION
AREA OF APPLICATION:
The
intimus
120
SP2(SC2)/CP4(CC3)/
CP5(CC4)/CP6(CC5)/CP7(CC6) data shredder
is a machine used for shredding general
documents.
Generally the machine may only be
used to shred paper (deviations see
table below "special materials")!
Shredding of other types of data carriers
may lead to injuries (for example due to
splintering of hard materials etc.) and
damage to the machine (for example
destruction of the cutter etc.).
INSTALLATION:
- Unpack the machine and put it together.
- Fit the plastic bag onto the bag frame.
- Connect the machine to the power with the
plug (1) (Fig. 2) (For information on the right
fuse for the plug see "TECHNICAL DATA").
The socket outlet shall be installed
near the equipment and shall be easily
accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
6 = Control display (fig. 1)
"Material jam in machine"/ "Light barrier
covered when door opens or when
machine turned on"
For the procedures see the relevant
description under the "MALFUNCTION"
section.
a) "Material jam in machine"
Comes on when too much material has
been fed into the cutters. The cutters
jam, then run in reverse for a short time
and stop. The motor switches off.
b) "Light barrier covered
when door open"
Comes on when there is still material in
the feed slot when the door is opened.
The cutters stop. The motor switches
off.
c) "Light barrier covered
when machine turned on"
Comes on when there is still material
in the feed slot when the machine is
switched on.
11
fig. 3
5
Advertenties
Inhoudsopgave
