Download Inhoudsopgave Inhoud Print deze pagina

LUND 67900 Handleiding pagina 15

Inhoudsopgave

Advertenties

Beschikbare talen
  • NL

Beschikbare talen

  • DUTCH, pagina 65
GB
attachment.
Tighten the adjusting screw at the front of the socket, but do not tighten it fully.
Place a cap on top of the attachment to prevent the juice from spilling out during squeezing.
There will be juice coming out through the small openings in the cap, so you should put a container of such a diameter as to
prevent the juice from spilling over during operation.
The fruit pulp will be squeezed out of the front opening of the cap. The tightness of the screw must be adjusted by observing
the results of the extrusion. Do not allow juice and pulp to clog the inside of the attachment. Excessive juice build-up inside the
attachment can cause fl ooding of the drive, which can damage the product and cause electric shock.
If the pulp coming out of the opening is excessively dry, loosen the screw slightly. This will help avoid clogging of the attachment.
Fruits with a higher juice content should be squeezed with a more-tightened screw. Less juicy fruit should be squeezed with a
less-tightened screw.
Kebbe attachment (XI)
Connect the attachment body to the mounting socket and insert the grinding auger into the body.
The rear part of the kebbe cap is equipped with positioning tabs, which should fi t into the notches in the front of the attachment.
Insert the front part of the socket into the kebbe cap and secure by tightening the fi xing nut.
Grating and shredding attachment (XII)
The attachment has a separate body and a separate pusher.
Install the attachment body into the drive socket.
Slide the drum into the body. The openings in the drum are very sharp and must be handled with care to avoid injury.
The attachment axis tabs should align with the notches in the opening in the rear wall of the drum (XIII).
Check that the pusher can be easily inserted and removed from the inlet opening.
Caution! Do not use the grinder attachment pusher in this attachment.
The product is equipped with three types of drums. Two drums with round openings are used for grating. The larger the openings,
the larger the shavings. The drum with rectangular openings is used for shredding.
After mounting the selected attachment, place a container under its outlet. The product is ready for use.
Starting the device
Make sure that the switch is in the OFF position, then plug the power cord into the socket.
The product has a switch which can be set in three positions.
OFF – product switched off ,
ON – product switched on,
R – reverse mode.
The device will be started after fl ipping the switch to the ON position. The switch does not need to be held in this position.
The device is switched off when the switch is set to the OFF position. To do this, press the button in the spot marked with "R" lightly
and release. Wait until the motor stops.
The switch position marked with "R" is intended for short engaging of the reverse gear. Press and hold the power switch in this
position. The auger starts to rotate in the opposite direction, which allows you to clean the inside of the food attachment. Releas-
ing the pressure on the switch will automatically return the switch to the OFF position, thus stopping the operation of the device.
Use reverse gear when the performance of the machine is reduced. Turning the auger in the opposite direction allows the food to
be withdrawn from the inside of the attachment. Next, restart the device by fl ipping the switch to the ON position and then grind
the food again. If you still notice a decrease in performance, stop the device operation, disconnect the attachment, disassemble
and manually clean it according to the instructions in the "Product Maintenance" section.
When you have fi nished using the product, turn it off by fl ipping the switch to the OFF position, then unplug the product's power
cord from the socket and begin maintenance activities on the product.
MAINTENANCE AND STORAGE
CAUTION! Never immerse the drive housing in water or other liquids. This may result in electrical shock and will damage the
product. All components of the attachments can be immersed in water or washed under the jet of water.
Parts of the device which have been in contact with food should be cleaned immediately after use. Dried food residues can clog
the components of the product, which can lead to a loss of performance or even damage the product. If this happens, immerse
these parts which were described as immersible in warm water with dishwashing liquid and leave it to soak, then clean with a
soft sponge or a brush and water with dishwashing liquid. None of the parts of the device is suitable for washing in mechanical
dishwashers. This can lead to the loss of shape, colour and texture of the materials they are made of.
Clean the openings in the juice-squeezing attachment and the grinder attachment strainers with a soft plastic brush. Do not use
sharp objects (including scouring sponges) to clean any part of the product.
O R I G I N A L
I N S T R U C T I O N S
15

Advertenties

Inhoudsopgave
loading

Gerelateerde Producten voor LUND 67900

Inhoudsopgave