Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
beep when you reach the maximum level
•
is the reduce fire crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off
•
is the increase fire crackling sound. Press this to increase the volume of the crackling sound.
CAS1000
Mains Switch 'A':- Controls the electricity supply to the appliance.
Note: This switch must be in the 'ON' ( I ) position for the appliance to operate
Button panel 'A':- Controls the functioning of the left side of appliance
•
is the on/standby button. Press it to turn on and off the flame effect. Turning it on will be indicated by the light
activating. Although the main lights operate immediately it will take a further 45 seconds before the flame effect
starts.
•
is the BlueTooth button. This will pair your remote control to the receiver. See 'Remote Control Operation' for
details
•
is the test mode button. This will be used by the manufacturer and the Service Engineer
•
is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level
•
is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level
•
is the reduce fire crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off
•
is the increase fire crackling sound. Press this to increase the volume of the crackling sound.
Button panel 'B':- Controls the functioning of the left side of appliance
•
is the test mode button. This will be used by the manufacturer and the Service Engineer
•
is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level
•
is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level
•
is the reduce fire crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off
•
is the increase fire crackling sound. Press this to increase the volume of the crackling sound.
GETTING THE DESIRED FLAME EFFECT
1. Switch the appliance on by pressing the main switch to the on position and pressing the on/standby button. The
flames will start after 45seconds. The flames will be at max height for 5seconds and then reduce to a nominal level
2. Press the
and
to the changes you make.
3. Do not tilt or move the appliance while there is water in the tank or sump
4. Make sure that the appliance is on a level surface
Once you have made you adjustments to both the flame height and crackling sound the appliance will keep these
settings even if you power off the appliance by either the on/standby button or by the main switch. The next time you
switch on the appliance it will start up as normal, wait 45 seconds for the flames to start, run at maximum height for 5
seconds and then revert to the adjusted settings.
BLUETOOTH RECEIVER CONTROLS
There are manual controls on the BlueTooth Receiver
CAS500
•
is the on/standby button. Press it to turn on and off the flame effect.
•
is the fire crackling sound. Press this to turn on and off the crackling sound. The volume is adjusted on the
manual controls of the appliance
•
is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level
•
is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level
CAS1000
•
is the on/standby button. Press it to turn on and off the flame effect.
•
is the fire crackling sound. Press this to turn on and off the crackling sound. The volume is adjusted on the
manual controls of the appliance
buttons to adjust the flame to your desired level. Please give the flame generator time to react
Advertenties
Inhoudsopgave
