Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
General Information
Only use filtered water in this appliance.
Unpack the appliance carefully and retain the packaging for possible future use, in the event of moving or returning the
fire to your supplier.
Always ensure that the appliance is sitting on a level surface.
The appliance is a flame effect only.
The appliance is designed to be built into a surround or built into a wall.
Before connecting the appliance, check that the supply voltage is the same as that stated on the appliance.
Please note: Used in an environment where background noise is very low, it may be possible to hear a sound which is
related to the operation of the flame effect. This is normal and should not be a cause for concern.
Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.
The water tank, sump, sump lid, tank cap and air filters must be cleaned once every two weeks, particularly in hard
water areas.
If you intend not using the appliance for longer than 2 weeks, drain the water from sump and water tank and dry the
sump.
The sump and the water tank in this product are treated with a biocidal product, Silver Biocide. This conforms with the
latest relevant ISO standard
Do not drink the water from the sump or from the water tank(s)
This appliance is intended to be permanently connected to the water mains and not connected by a hose-set
Installation Instructions
This section describes how to set up your fire.
BEFORE YOU START
1. Ensure that all packing items are removed (read any warning labels carefully) and retain all packing for possible
future use.
2. Before connecting the appliance, check that the supply voltage is the same as that stated on the appliance.
3. Ensure that the appliance is sitting on a level surface
4. Lift off the metal top plate to gain access to the appliance. Keep the top plate with the packing for possible future
use. (Fig.2)
Installation Guide
This product can be built into a wall, surround or structure. Please take note of the product dimensions in Fig.1 and
build your wall, surround or structure accordingly. You are required to leave a minimum of 400mm from the base of the
fuelbed to any shelf/enclosure above the product. This will allow enough space above the product to allow the flames to
form fully and not to be obstructed.
This product needs free ventilation from underneath to operate correctly. The free ventilation helps keep the electronic
components cool, allow the mist to evacuate the sump and lift out of the product effortlessly.
THE AREA OF FREE VENTILATION THE CAS500 REQUIRES IS A MINIMUM OF 210CM
THE AREA OF FREE VENTILATION THE CAS1000 REQUIRES IS A MINIMUM OF 420CM
Surround Design
The CAS500 and CAS1000 are designed to be built into a surround/wall. Using the dimensions provided in Fig1. you
can design a cavity for the appliance. Be sure to allow room under and around the appliance for the water connection
and the electrical connection. Once the surround/wall is prepared you can put the appliance in place. Fit the LED Log
Fuelbed so you ensure that the appliance is centered, see section 'Assembling the LED Log Fuelbed'. When you have
settled on a position, lift off the Fuelbed and using appropriate screws for the surround/wall, screw through the formed
holes in the left and right side panels securing the appliance in place.
Water Supply
The appliance can operate by using the water tank(s) provided or by connecting up mains water.
Water Tank(s): You will need to remove the 'Fill Cap' from the sump. (Fig.3a and Fig.3b). Place the Water Tank(s)
(Fig.3C) in your sink and remove the cap (turn anti-clockwise). Fill the Water Tank with filtered tap water only. This is
necessary to prolong the life of the flame and smoke producing unit. The water should be filtered through a conventional
domestic water filter unit and the filter should be replaced regularly. Distilled water must not be used.
Mains Water: If you choose to supply mains water to the appliance store the bottle(s) with the metal top plate and
packaging. You can use the Piercing Valve (supplied) to connect into your mains water supply by;
1. Clamp the Piercing Valve onto you water pipe: maximum 1/2" (12.7mm) pipe
2. Connect a 1/4" (6.35mm) PVC tube (not supplied) from the piercing valve into the water filter supplied and then in
to the product (Fig.4).
3. Turn the tap on the valve clockwise to pierce into the water pipe. Turn the tap anti-clockwise to allow the water to
flow through the valve. You can shut off the water to the product by turning the tap on the valve clockwise until the
flow stops.
4. Turn on the internal ball valve. This is located under the sump. Remove the sump as described under 'Cleaning' in
.
2
.
2
Advertenties
Inhoudsopgave
