Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Clean the spray gun
•
before each change of spraying material
•
at least once a week or
•
several times a week if required by the spraying medium and depending on the
degree of fouling.
Complete Cleaning
1.
Disassemble the spray gun.
2.
Clean the air cap and the material nozzle with a soft brush and cleaning fluid.
3.
Clean all other components and the gun body with a soft cloth and cleaning fluid.
4.
Coat the following parts with a thin layer of grease:
•
needle spring
•
all sliding parts and bearing points.
The moving internal parts must be greased at least once a week.
The springs should always be coated with a thin layer of grease. For this, always use
a non-acidic, non-resinogenic grease and a soft brush.
Assemble the gun again in reverse order.
Attention
Do not use any hard, sharp or pointed objects when cleaning the spray gun.
WALTHER is not responsible for any damage resulting from improper cleaning.
10
Waste Disposal
Waste spraying media and waste material from cleaning and servicing must be
disposed of in accordance with all applicable local and national regulations.
Warning
Observe the instructions issued by the manufacturers of the spraying and cleaning
material at all times. The improper disposal of waste material endangers the health
of human beings and animals!
36
11
Technical Data
PILOT III F
Net weight
590 g / 1.3 Ib
Pressure ranges:
Max. input air pressure
Max. material pressure
Air cap*
High-Pressure
Nozzle sizes optional:
• 0,5 • 0,8 • 1,0 • 1,2 • 1,5 • 1,8 • 2,0 • 2,5 • 3,0 • 3,5 mm ø
Air Cap
Max. operating tempera-
43 °C / 109.4 °F
Noise level (measured at approx.1 m
from the spray gun)
ture
Connections:
Atomizing Air
1/4"
Material Inlet
3/8"
*Other air caps available on request.
PILOT III F-MP
Net weight
590 g / 1.3 Ib
Pressure ranges:
Max. input air pressure
Max. spraying air pressure
Max. material pressure
Air cap
Medium-Pressure
Nozzle sizes optional:
• 0,5 • 0,8 • 1,0 • 1,2 • 1,5 • 1,8 • 2,0 • 2,5 mm ø
Air Cap
Max. operating tempera-
43 °C / 109.4°F
Noise level (measured at approx.1 m
ture
from the spray gun)
Connections:
Atomizing Air
1/4"
Material Inlet
3/8"
PILOT III K
Net weight
590 g / 1.3 Ib
Pressure ranges:
Max. input air pressure
Max. material pressure
Air cap
High-Pressure
Nozzle sizes optional:
1,0 • 1,5 mm ø
Air Cap
Max. operating tempera-
43 °C / 109.4°F
Noise level (measured at approx.1 m
ture
from the spray gun)
Connections:
Atomizing Air
1/4"
Material Inlet
3/8"
Air consumption:
PILOT III F
Atomising air
6-hole-air cap
pressure
Round jet
Flat jet
1,0 bar/ 15 psi
88 l/min
142 l/min
2,0 bar/ 29 psi
138 l/min
217 l/min
3,0 bar/ 44 psi
186 l/min
288 l/min
4,0 bar/ 58 psi
222 l/min
351 l/min
5,0 bar/ 73 psi
274 l/min
432 l/min
6,0 bar/ 87 psi
317 l/min
488 l/min
Right to effect technical changes reserved.
37
8 bar / 116 psi
8 bar / 116 psi
85 dB (A)
3,3 bar / 47.8 psi
1,4 bar / 20.3 psi
8 bar / 116 psi
83 dB (A)
8 bar / 116 psi
8 bar / 116 psi
85 dB (A)
PILOT III F-MP
PILOT III K
Medium-pressure air cap
High-pressure air cap
Round jet
Flat jet
Round jet
Flat jet
140 l/min
190 l/min
200 l/min
270 l/min
190 l/min
270 l/min
275 l/min
380 l/min
230 l/min
330 l/min
325 l/min
450 l/min
260 l/min
390 l/min
375 l/min
525 l/min
290 l/min
405 l/min
400 l/min
575 l/min
300 l/min
425 l/min
450 l/min
625 l/min
Advertenties
Hoofdstukken
Inhoudsopgave
