Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Features
1.
POWER IN: Use the included power
adapter to connect the mixer to a
power outlet. While the power is
switched off, plug the power supply into
the mixer first, then plug the power
supply into a power outlet.
2.
POWER SWITCH: Turns the mixer on
and off. Turn on the mixer after all input
devices have been connected and
before you turn on amplifiers. Turn off
amplifiers before you turn off the mixer.
3.
MIC INPUT: Connect a microphone to
these inputs with an XLR cable.
4.
LINE INPUT *: Connect
devices to these inputs with 1/4"
cables.
5.
GAIN: Adjusts the channel audio level
(pre-fader and pre-EQ gain). Adjust this
so that the PEAK LED just barely lights
up during the loudest parts of the song.
6.
HI EQ (TREBLE): Adjusts the high
(treble) frequencies of the channel.
7.
MID
EQ:
Adjusts
frequencies of the channel.
8.
LO EQ (BASS): Adjusts the low (bass)
frequencies of the channel.
9.
AUX SEND 1 MON: Adjusts the
channel audio (pre-EQ) level that is sent
to the AUX SEND output labeled "1
MON." You can use this to create a
custom monitor mix for yourself or your
musicians.
10.
AUX SEND 2 FX: Adjusts the channel
audio (post-EQ) level that is sent to the
mixer's internal effects processor. Turn
this up for the channels that you want internal
effects applied to. You can use this to apply
external effects to individual channels.
11.
CHANNEL PAN: Adjusts the (mono) channel's
position in the stereo field.
12.
BALANCE (CH 3/4 & 5/6): Adjusts the balance
between Channels 3 and 4 and Channels 5 and 6.
13.
PEAK LED: The LED will flash if the signal is
clipping. If this happens, decrease the setting of
the GAIN knob or CHANNEL VOLUME knob.
14.
CHANNEL VOLUME: Adjusts the audio level on
the channel.
15.
AUX RETURN INPUTS **: You can connect the
outputs of an external device to these inputs with
1/4" mono cables. This is usually used for
outboard effects devices but can also be used like an extra input channel for synthesizers, drum
machines, etc. If your source is mono, plug it into the left jack and it will be heard on both the left and
right sides.
16.
AUX SEND OUTPUTS **: You can use a 1/4" TRS cable to connect the AUX 1 MON output to the
input of an external amplifier or active monitor to create a custom monitor mix for onstage musicians.
You can adjust this level with the AUX RETURN LEVEL knob labeled "TO AUX 1 MON." To use an
external effects rack unit, compressor, etc. with the mixer, you can use a Y-cable to connect the AUX
2 FX output to the input of your external device, then connect the outputs of the device to the AUX
RETURN INPUTS of the mixer.
line-level
the
mid-range
10
11
13
14
1
2
3
3
4
4
5
6
7
8
9
11
12
* When using LINE INPUTS 3/4, 5/6 and the AUX
RETURNS:
• If only the left channel is used, the signal will
be heard in both left and right channels and
the balance will not be adjustable.
• If only the right channel is used, the signal will
be heard in the right channel only.
** To use an external effects rack unit,
compressor, etc., use a Y-cable (1/4" stereo to
two 1/4" mono) to connect the AUX SEND "2
FX" output to the left and right inputs your
external device. Connect the outputs of your
external device to the left and right AUX
RETURN INPUTS.
21
4
15
16
17
17
15
16
19 19 20 20
22
23
24
25
2 TK
12
26
27
2 TK
18
18
2 TK
31
30
29
28
3
Advertenties
Inhoudsopgave
