Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Operating Instructions - See Fig. 3
Icon Display
Funtion
Power /
A
-
Standby
Flame
+
Flame
-
B
Down
Flame
fc
Cycling
-
Sleep
C
Timer
Low
Heat
D
High
Heat
Cool
Blow
-
Temp
E
-
Temp
F
-
Down
LED
-
G
COLOUR
User Modes:
Mode Name /Discription
Change Celsius (
C) to Fahrenheit (
0
Description
Press Once to turn the product 'ON'.
Press a second time to put the product into 'STANDBY'
(When returning from 'STANDBY' mode the product will return to previous settings unless
the product has been unplugged, in which case it will reset to factory settings)
'FLAME EFFECT' button this turns the flame effect ON or OFF independently of the
products other features.
This Button will increase the brightness of the flame effect. There are 5 brightness settings
Up
shown as F1, F2, F3, F4, F5. This button will ONLY increase the brightness level.
This Button will decrease the brightness of the flame effect. There are 5 brightness settings
shown as F1, F2, F3, F4, F5. This button will ONLY decrease the brightness level.
This setting is set by pressing the Flame Up button once more after F5. this will cause the
brightness of the flame effect to cycle from F2 to F5 in a continuous Loop.
This will turn the flame effect off. If the heater is ON, the display will activate and remain
Off
active to read the set temperature and show if the product is on LOW HEAT/ HIGH HEAT/
COOL BLOW.
Press multiple times to change the 'SLEEP TIMER' in 0.5 hr increments from 0.5
hr to 8.0 hr before turning off. The remaining time on the 'SLEEP TIMER' displays.
(This icon is Green in Colour)
'HEAT' button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT,
COOL BLOW and OFF. The heat setting will be indicated by an icon in the display see Fig.1.
When the flame effect is 'ON' the display will turn off after 5 seconds, however if the
heater is being used independently of the flame effect. The low heat or high heat icon
will appear continuously in the display.
This setting will run the heater at 'LOW HEAT' this setting will be indicated by the 'LOW HEAT'
icon. To Adjust the temperature setting the Temp Down or Temp Up buttons described
below must be used.
(This icon is Orange in Colour)
This icon in the display indicates 'HIGH HEAT' this setting will be indicated by the 'HIGH
HEAT' icon. To Adjust the temperature setting the Temp Down or Temp Up buttons
described below must be used.
(This icon is Red in Colour)
This icon in the floating display indicates 'COOL BLOW' this setting will be indicated by
the 'COOL BLOW' icon and the letters 'CB' appearing in the display.
(This icon is Blue in Colour)
This switches the heater and blower 'OFF', no icon will be displayed in the display. Note
Off
the blower will run for 5-10 seconds after being turned off, this is to ensure the product
cools down safely.
Press multiple times to increase the heater temperature in 1
temperature that can be set 30
Up
When High Heat is selected, the letters 'HH' appear in the display, this means the heat
will remain ON continusously and is not controlled by the thermostat.
Press multiple times to lower the heater temperature in 1
temperature that can be set is18
Press multiple times to change the colour of the LED mood lighting and the coloured
fuel bed. The colour can be set as Orange, Red, Green, Blue, or cycling through all four
colours continuously.
Action (Actions cannot be input by remote control)
Press both 3 Dot Button (
F)
0
and display flashes. (To revert back to Celsius repeat this action)
0
C.
0
C.
) and 2 Dot (
) on the unit and hold until beep is heard
C increments. The highest
0
0
C increments. The lowest
Advertenties
Inhoudsopgave
