Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Assembly
When drilling the bores and tightening the screws, make sure not to damage
any power lines or gas or water pipes distributed below the surface. The as-
sembly and the installation of the device must be carried out by a specialist
who is familiar with the hazards and the relevant regulations. The mainte-
nance, operation and commissioning of this product may only be carried out
by qualified personnel.
When selecting the location for installing your device, take care that it will
not be subjected to shaking, vibrations, dust, heat, cold and moisture. When
using a fog machine, make sure that the LED light effect is not subjected to a
direct stream of fog. Furthermore, keep the product away from strong trans-
formers or motors.
The light effect may only be operated in locations where the ambient tempera-
ture is less than 40 °C.
Never cover the unit. When installing with other equipment, make sure that
there is sufficient ventilation. Keep a sufficient distance from other devices
and walls. Do not install the light effect device near heat sources. Do not point
any strong beams or light sources onto the device. This may lead to overheat-
ing (risk of fire).
Do not drill or screw additional screws in the housing in order to fasten the
device. Contact with dangerously high voltages could become possible.
The device must be mounted out of normal reach.
This symbol indicates the minimum distance to the illuminated sur-
faces. Illuminated objects must be at least 0.5 m away from the device's light
outlet. Easily-flammable materials, such as decorative fabrics too, must be at
least 0.5 m away from the device. Otherwise, such materials may catch fire!
Never apply filter films, masks, or other materials on the light output. This can
cause heat damages or fire risk.
During installation and servicing, the area below the installation site must be
cordoned off.
The installation surface or mounting fixture must be designed so that it can
withstand ten times the loading capacity for at least one hour without perma-
nent damaging deformation.
It is also essential that the device is secured by means of a second safety
restraint, which is separate from the proper mounting supports, when it is
installed in an elevated position. If the main supports fail, no part of the instal-
lation should be able to fall down.
Observe all the relevant regulations in your country when installing the de-
vice.
Acceptance test (in case of industrial/public use):
Before using the product for the first time and after any significant modifications, the
installation (including the electrical connections) must be checked by a specialist.
An annual check by a technical expert is required.
• Secure the effect spotlight with the mounting bracket to the ceiling or a suitable crossbar
system. For installation with a screw, there is an attachment hole in the mounting bracket.
During installation, make sure that the device cannot swing freely. Use mounting materials
that are compatible with the fastening surface and capable of bearing the weight of the light
effect device.
• When installing in an elevated location, also secure the device with a suitable safety restraint
cable or safety net. The safety restraint cable or net must be capable of supporting the light
effect device in the event of a fault in the main support system.
• Set the desired inclination angle and tighten the two locking screws on the mounting bracket
securely.
For commercial or public use, a number of regulations and restrictions are to
be observed, which are described here only in excerpts. You as the operator
are responsible that these regulations are adhered to during installation and
operation.
All manuals and user guides at all-guides.com
Mains connection
• Plug the power plug of the mains cable into an earthed wall socket.
Initial operation
After connecting the power plug to the power grid, the device is ready for use.
• The mains switch on the back of the device is used to switch the appliance on and off.
• By means of the potentiometer on the back of the device, you can adjust the sensitivity of the
Replacing the fuse
If you have to replace fuses, ensure that you only use fuses of the same type and rated current
(see „Technical data").
• Disconnect the product from the mains supply before each fuse replacement. Remove the
• Use a suitable screwdriver to open the fuse holder. Unscrew the fuse holder by turning it
• Remove the faulty fuse and replace it with a fuse of the same type.
• Carefully push the fuse holder with the new fuse back into the fuse unit.
• The fuse holder must be fastened turning the screw in a clockwise direction.
• Only then may you reconnect the device to the mains and place it back into operation.
Maintenance and cleaning
The product is maintenance-free for you. The product contains no parts that require servicing.
Therefore, do not open it. The LED illuminants used are permanently installed; they cannot be
replaced.
• Disconnect the product from the mains supply before each cleaning procedure.
• The device can heat up during operation. Do not touch the housing when in operation. Allow
• Never use aggressive cleaning alcohol or other chemical solutions, since these could dam-
• Use a dry, lint-free cloth to clean the product.
The mains socket to which the light effect device is connected must be in
close vicinity to the device and easily accessible, so the device can be quickly
isolated from the mains power supply in the event of a fault.
Be careful when handling the mains cables and mains connectors. The mains
voltage can cause serious electric shocks, which can be fatal.
Make sure that the connecting cable is not pinched or damaged by sharp
edges when making the connection.
Do not leave the cables trailing free; route them in an orderly and professional
way to prevent accidents.
Before plugging in the mains plug make sure the voltage indicated on the light
effect device is compatible with the mains voltage available. Do not connect
the device if the data does not match the available mains voltage. The wrong
supply voltage may lead to irreparable damages to the device and involve
risks for the user.
music control to the volume of the music. Use a suitable screwdriver to do this.
Adjust the potentiometer so that the light effect changes to the
beat of the music.
Fixing fuses or bridging the fuse holder is not permitted.
mains plug from the mains socket.
counter-clockwise. Remove the fuse holder with the fuse.
the light effect device to cool down after operation before you touch or clean the housing.
age the enclosure or even impair operation.
The device should be cleaned at regular intervals. Heavy contamination or
dust can adversely affect the insulation resistance of the device.
Contamination removal may be carried out only by qualified personnel who
are familiar with the hazards involved and the relevant regulations.
Live components may be exposed if the covering is opened or components
are removed.
Other service work or repairs may be carried out only by qualified personnel
who are familiar with the hazards involved and the relevant regulations.
MIC
Advertenties
Inhoudsopgave
