Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
INSTRUCTIONS FOR INSTALLATION
Foreword
Dear Customer,
We would like to thank you for buying this DRU product.
Our products have been designed and produced to meet
the highest possible quality, performance and safety
requirements, allowing you to enjoy years of problem-free
use.
In this booklet you will find instructions for the installation
and use of your new appliance. Please read these instruc-
tions and the manual carefully to familiarize yourself with
the appliance. If you require any further support, please do
not hesitate to contact your supplier.
Unpacking
Once the heater has been unpacked, all packaging should
be disposed of in the regular manner.
Connection
This appliance should be connected by a registered
installer.
INSTRUCTIONS FOR INSTALLATION
Type of gas
This appliance can only be used and is only suitable for the
country and the type of gas mentioned on the type identi-
fication tag. Please check that the local gas and pressure
correspond with the specifications on the type identifica-
tion tag. All regulations regarding gas installation, including
any local regulations, must be observed at all times.The
appliance is to be installed by a competend person.
To operate the heater suitable for natural gas on bultane
or propane, it should be converted by a competend per-
son. A conversion set can be ordered through your
supplier.
Important
• Keep curtains and any other flammable materials at least
50cm away form the appliance.
• Caution! Touching the heater when hot can cause burns
and blisters!
• The appliance should be installed and maintained by a
registered installer.
• Do not install any so-called dust filter on or under the
casing.
• Do not hang wet clothes and towels etc. on the heater to
dry.
General
The appliance can be mounted either on a wall of incom-
bustible material (e.g. stone or concrete) or on a wall of
combustible material (e.g. wood).
Installation to a wall of non-flammable material
(fig. 7, 9, 11, pg. 58-60)
DRU-ART Models 2, 3 and 4 can are suitable for hanging
installation only, DRU-ART Models 5, 6, 8 and 10 are suita-
ble for either hanging or freestanding installation. Allow at
least 1 metre's clearance above the heater to enable suffi-
cient heat circulation.When installed hanging, at least 1 m
free space should be kept above the appliance to allow suf-
ficient heat dissipation.When intalled standing, the bottom
of the mounting sheet (2) should stand on the floor, this is
the minimum height between the floor and centre of wall
duct (size F. fig 7, 9, 11, pg. 58-60).
The mounting plate (2) serves as a template to mark the
position of the duct.To be able to hang the casing over the
interior, a minimal clearance of 25 mm must be allowed
between the appliance and a windowsill or suchlike.The
minimum clear installation height (Y) required for each of
the various models is listed in the table on page 61.
The standard wall duct
Drill a horizontal hole in the wall, ø E to take the air-sup-
ply pipe.The wall duct should slope at an angle of approx. 2º.
The standard wall duct is suitable for walls with a thick-
ness of 50 – 330 mm and the standard extended wall duct
for walls with a thickness of 50 – 600 mm. Depending on
the thickness of the wall, the inlet and outlet pipes should
be made to length, i.e.:
Length of inlet pipe
DRU-ART 2
Thickness of wall + 20mm Thickness of wall + 40mm
DRU-ART 3, 4
Thickness of wall + 20mm
DRU-ART 5, 6
Thickness of wall + 20mm
DRU-ART 8,10 Thickness of wall + 20mm
The tension members fixed to the wall grid can be made
to size after installation
Installation of the standard exterior wall duct
(fig. 1, 3, 5, page 57/58)
Slide the adjusted inlet pipe (1) through the mounting
sheet (2), with the turned-back edge facing the mark (45º
top left) in the mounting sheet. Slide the sealing ring (3)
and the wall ring (4) around the inlet pipe, paying attention
to the order (see figure).Take the whole and slide the inlet
pipe into the wall opening. Press the mounting sheet up to
the wall. Press the inlet pipe back in such a way that the
end of the pipe is level with the turned-back edge of the
mounting sheet.
From the outside, bring the wall grid with its attached ten-
sion members into the inlet pipe. Bend the tension mem-
bers a little outwards, so that they will jam slightly in the
inlet pipe, keeping the grid in its place. Keep the mark
"Top" up when placing the wall grid. Slide the two fastening
clamps (5) over the tension members (6), taking care that
the fastening clamps catch on the turned-back edge of the
10
Length of outlet pipe
Thickness of wall + 30mm
Thickness of wall + 70mm
Thickness of wall + 35mm
Advertenties
Hoofdstukken
Inhoudsopgave
