Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
6 Product Overview
6.1 Product
2
3
4
5
6
1
LCD screen
3
ON/OFF button
5
Starter cables socket
7
USB-C®: input/output
9
USB-A: output
6.2 Display
B
C
D
A
Product battery %:
charge / discharge / standby
C
OUT: Output connected
E
USB-C® connected
G
BOOST:
Ready to jump start the vehicle
I
Warning, see section:
Warning messages [} 5]
6.3 Starter cables
B
A
Starter cables plug
C
Red starter clamp (+)
7 Charge the product
Tip:
Use a 45W fast charger to maximize recharging performance.
Preconditions:
a
You have a suitable power adaptor.
5
1
7
8
9
2
BOOST button
4
DC output jack
6
Ports cover
8
USB-A: output
A
E
F
G
B
IN:
Input connected
D
USB-A connected
F
DC jack connected
H
Charging / discharging power
A
C
B
Black starter clamp (-)
1. Connect one end of the included USB-C® cable to a power adaptor.
2. Connect the other end of the cable to the USB-C® input on the product.
3. Press the
à
The battery capacity will show on the display.
à
The display will switch OFF when charging is complete.
8 Connection
8.1 Preparation for connection
Before connecting the cables to a battery:
■
Switch OFF all vehicle electrics (e.g. air conditioner, heater, radio, lights etc.).
■
Make sure the ignition key is in the "OFF" position. For push-to-start ignition, make sure
the vehicle is completely OFF.
■
Check the battery contact terminals are clean.
■
Prepare your vehicle for ignition (e.g. place gear in park and engage the emergency
brake).
8.2 Connecting the leads
Important:
Always connect test leads to terminals in the correct order.
1. Connect the red clamp to the positive (+) terminal.
2. Connect the black clamp to the negative (-) terminal.
3. Wiggle the clamps back and forth to ensure proper connection.
8.3 Disconnecting the leads
When finished using the product:
1. Disconnect the red clamp.
2. Disconnect the black clamp.
9 Operation
Important:
Fully charge the product before using it for the first time. See section:
[} 5]
9.1 Jump start the vehicle
H
Preconditions:
a
The product is at least 50% charged. See section:
I
a
The vehicle is prepared for connection. See section:
1. Connect the starter cables. See section:
2. Press the
3. Press and hold the BOOST button until BOOST appears on the display.
4. Start the vehicle engine.
à
An alarm will sound if any protection mechanisms activate. See section:
messages [} 5]
5. If the engine starts, disconnect the starter cables. See section:
[} 5].
6. If the engine does not start, switch the ignition OFF and repeat steps 3 & 4.
Important:
Let the vehicle run for approximately 30 mins. to recharge the battery.
9.2 Power bank
Preconditions:
a
To use this product as a power bank you will need a suitable charging cable.
1. Connect one end of the charging cable to your mobile device, and the other end to an
output on the product.
2. Press the
3. Disconnect the cable when charging is complete.
Note:
DC output port
– The DC output port is capable of delivering 15V 10A.
– Use it with the included auxiliary power outlet to DC male cable adaptor.
9.3 LED light
1. Press and hold the
2. Press the
ing → OFF.
10 Warning messages
If a protection mechanism activates, an alert will sound and a warning message will appear
on the display.
button to start charging.
Charge the product
Connecting the leads
button to switch the product ON.
button to start charging.
button to switch the LED ON/OFF.
button repeatedly to cycle through modes: constant ON → SOS → flash-
Charge the product
[} 5].
Preparation for connection
[} 5].
[} 5].
Warning
Disconnecting the leads
Advertenties
Inhoudsopgave
