Eldom Invest RH01F20W-S Technische Handleiding pagina 18
Verberg thumbnails
Zie ook voor RH01F20W-S:
- Handleiding voor installatie, gebruik en onderhoud (45 pagina's)
Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
EN
Controllers features and settings
Setting specific temperature
Use buttons 2 and 3 to change the temperature. The maximum temperature that can be set is 28 °C and the
minimum is 7 °C. Pressing any of these two buttons shall display the current temperature set. With the following
keystrokes you may change the assignment in the desired direction. If no new button is pressed within 5
seconds, the new task shall be memorized and automatically the unit shall switch to the main screen. If any of the
buttons 2 or 3 shall be held for more than 0.7 s, the temperature set point value automatically starts to increase or
decrease with the speed of 4 units per second.
Adjusting the power of the appliance
When the measured temperature is lower than the set one, the convector heater switches on - its power indicator
scale fills in. The more the temperature is approaching the set one, the less is the filling of the scale. When the set
temperature is reached, the indicator goes out. The power control function can be switched off by the sub-menu
Settings by deactivating the check-mark Reg. power. In this case, under all operating modes, the convector
heater shall run at full power during heating or shall be completely switched off when the temperature set is
reached.
Child lock
This feature locks all control panel buttons, limiting the possibility of unauthorized access to the controller
settings. The feature is turned on by the child protection sub-menu, followed by the instruction on the display -
Press OK to lock the buttons. The following message is displayed - Buttons are locked!. It is suitable to press the
button 1 to exit the settings menu, displaying a symbol illustrating child protection. To turn off child protection, you must hold the OK button
for a time longer than 7 seconds.
Protection against convector heater falling
If the convector heater is knocked down while switched on, the controller switches off the heater, the unit displays a message Convector
fell, and activates an audible alarm. The alarm will be deactivated automatically after restoring the appliance normal position or by
pressing button 1 to switch off the convector heater. It may be a malfunction if the convector heater was stored in a cold place for a long
time and then placed in a significantly warmer place.
Open window feature
The controller has a built-in feature for recognizing an open window that automatically stops heating. An open window icon appears on the
display. This feature operates in two modes - Smart and On. Switching from one mode to the other is done by changing the setup Open
window in sub-menu System Settings. When the setting is Smart, the convector heater shall continue heating as soon as it detects that
the window is closed or after 15 minutes have elapsed since the protection mode is activated, while the heating mode ON shall continue
for 60 minutes once the mode is activated. The Open window feature is disabled when you press button 1, which switches the convector
heater to Standby mode, or from the sub-menu System set Open Win to Off
Keeping the system date and time
The controller unit keeps the system date and time
For all Timer / Program, Delayed Start, and Power Meters to work correctly, the date and time must be verified.
Verification is set from the main menu, sub-menu Time and Date. The auto-enable option check box works only
on models with WiFi control.
Two stage overheat protection
Apart from the electro-mechanical thermal protection, the convector heaters also rely on the electronic
protection built into the controller. This protection prevents accidental overheating of the appliance inside. The
feature temporarily interrupts the heating until the temperature drops below the allowed maximum. A symbol is
displayed.
Color graphic display
The electronics have a high-resolution color display. The Display sub-menu sets Brightness settings (from 1 to
10) and Dimming activation check-box. Dimming automatically reduces the brightness of the display 30
seconds after the last press of a button (the feature does not work at set brightness -1).
Reporting consumed electricity
The controller supports separate counters for daily and nocturnal electricity consumption. In order to report
correctly the concerned data, it shall be necessary to set the unit power from the sub-menu Settings - Power
setting, and the start time of each tariff in the Home tariffs sub-menu. When the OK button is pressed once, the
electricity consumption counters are displayed and the date and time of their last reset. While this screen is
displayed, if the OK button is held for 2 seconds, then the counters are reset and the resetting date and time are
recorded. Next time you press the OK button, it switches to the screens with a graph of the electricity consumed
by hours. The controller shall store such information for the last 7 days. By pressing the ▲ or ▼ buttons, the
charts shall change with the days for
which information is available. Each graph shows the date to which it refers and the total electricity consumed for
that day. It should be borne in mind that the information on the electricity consumed is calculated on the basis of
the convector heater set power.
All manuals and user guides at all-guides.com
18
EN
Advertenties
Inhoudsopgave
