Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
˜ Before use
˜ Unpacking
Remove the packaging . Check if the product is
damaged .
˜ Assembly
Accessory needed: Cross head screwdriver
Number of persons needed for assembly: 1 adult
Fig. Step
1 . Turn the extension pole
so that the L-shaped bolt
upwards .
2 . Remove the L-shaped bolt
C
washer
from the extension pole
[
16 ]
3 . Place the base
weight
on the extension pole
[
15 ]
4 . Fasten the washer
bolt
.
[
17 ]
1 . Turn the assembled parts from the previous
assembly step upside down . Place the
base
on the floor .
[
14 ]
2 . Loosen the lock screw
D
extension pole
3 . Place the motor unit's
the extension pole
on the back side . Tighten the lock screw
(motor bracket)
Remove the lock screws (M5 x 8 mm) (x 4)
E
(rear grille)
from the motor unit
18 ]
[
1 . Align the grille handle
to the rear . Attach the rear grille
F
motor unit (with upper pole)
2 . Tighten with the 4 lock screws
Point the groove on the motor shaft
G
upwards .
10 GB/IE/NI
upside down
[
13 ]
is directed
17 ]
[
and the
[
17 ]
[
13 ]
and the base
[
14 ]
.
[
13 ]
and the L-shaped
[
16 ]
from the
11 ]
[
.
[
13 ]
upper pole on
[
10 ]
. Align the hole
13 ]
[
.
11 ]
[
.
[
10 ]
upwards and
3 ]
[
to the
2 ]
[
.
[
10 ]
.
[
18 ]
4 ]
[
Fig. Step
1 . Loosen the lock screw
blade
on the blade's screw thread) .
Place the blade on the motor shaft
H
blade's rear with the lock screw is facing
the motor unit (with upper pole)
2 . Tighten the lock screw (M4 x 8 mm)
(blade)
1 . Open the grille clips (x 5)
grille
2 . Remove the lock nut and lock screw
(M2 .5 x 10 mm) (grille)
grille
I
3 . Hang the grille hanger
.
grille
NOTE: The grille clips (x 5)
over the frame of the rear grille
Insert the lock screw
J
nut
. Close the grille clips (x 5)
21 ]
[
grille frame .
˜ Height adjustment
Loosen the height adjustment knob
(positioned on the extension pole
counter-clockwise direction .
Adjust the length of the extension pole
Tighten the height adjustment knob
clockwise direction .
˜ Tilt adjustment
Loosen the knob (tilt adjustment)
Adjust the tilt angle manually .
Tighten the knob (tilt adjustment)
Do not perform the tilt adjustment when the
product is in operation .
from the
19 ]
[
(the lock screw is pre-assembled
1 ]
[
.
19 ]
[
[
20 ]
.
[
22 ]
21 ]
[
.
22 ]
[
of the front
23 ]
[
on the rear grille
22 ]
[
2 ]
[
. Fasten the lock
[
21 ]
13 ]
[
9 ]
[
9 ]
[
(the
[
4 ]
) .
10 ]
[
on the front
from the front
.
must fit
20 ]
[
.
[
2 ]
at the
[
20 ]
[
12 ]
) in a
.
13 ]
[
in a
[
12 ]
.
again .
Advertenties
Hoofdstukken
Inhoudsopgave
