Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
ENGLISH
Channel mode
Used to set the desired channel setup mode.
Press the MENU button until "ChMd" is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to choose 1MSL, 4MSL, 1Ch, 8Ch or 11Ch mode.
Once the desired channel setup mode shows on the display, press the ENTER
button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2
seconds.
Show Mode
Used to choose the Show mode when used in standalone or master/slave
mode.
Press the MENU button until "ShMd" is showing on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to select one of the available shows:
Show 1 (Sh 1): Fixture is placed on the floor. Tilt movement angle 210°.
Show 2 (Sh 2): Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 (Sh 3): Fixture is placed on a podium, in front of the audience. The
spot is always projecting to the audience's direction; i.e. in front of the stage.
Pan movement angle (left to right to left): 160°. Tilt movement angle: 90° (60°
above horizon; 30° below horizon.)
Show 4 (Sh 4): Fixture is fixed under ceiling. The spot is mainly projecting in
front of the stage. Pan movement angle (left to right to left):160°. Tilt
movement angle: 90° (vertically, front 75°; back 15°)
Once the right mode shows on the display, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2
seconds.
Split Color
You can select if the unit can only show full colors or also split colors.
Press the MENU button until "SPLC" is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select "Yes" (Split colors) or "No" (only full colors).
Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2
seconds.
Slave Mode
Used to make the slave unit work in opposite to the master or to work in
complete sync.
Press the MENU button until "SLMd" is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select "SL 1" (normal) or "SL 2" (2 light show)
mode.
Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2
seconds.
Blackout Mode
Blackout mode: when no DMX-signal is detected the unit goes in blackout
waiting for a DMX-signal.
No blackout mode: when no DMX-signal is detected, the unit automatically
switches to standalone. Press the MENU button until "bLMd" is shown on the
display.
JB SYSTEMS
®
OPERATION MANUAL
5/85
ENGLISH
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select "Yes" (blackout on) or "No" (blackout off) mode.
Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Sound State
The unit works to rhythm of the beat when used in standalone or master/slave mode
Press the MENU button until "SOUn" is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select "On" or "Off" mode.
Once the mode is selected, press the ENTER button save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Sound Sense
Used to set the sensitivity of the internal microphone
Press the MENU button until "SOSe" is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select a value between "0" (very low sensitivity) and "100" (high sensitivity).
Once the mode is selected, press the ENTER button save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Pan Inversion
Normal: Panning movement is not inversed.
Pan inversion: Panning movement is inversed
Press the MENU button until "IPAn" is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select "No" (normal) or "I" (pan inversion) mode.
Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Tilt Inversion
Normal: Tilt movement is not inversed.
Tilt inversion: tilt movement is inversed
Press the MENU button until "ItLt" is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select "No" (normal) or "I" (tilt inversion) mode.
Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Display on/off
Display on: display is always lit.
Display off: display is dark when not used.
Press the MENU button until the display shows "Led".
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to select "On" (display always lit) or "Off" (display dark when not used).
Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Display Inversion
Display normal: display is readable when the unit is on the floor.
Display inversion: display is readable when the unit is mounted upside down.
Press the MENU button until "dISP" is shown on the display. (normal display)
Press the ENTER button to toggle between
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
SIRIUS
JB SYSTEMS
(normal display) and
6/85
®
OPERATION MANUAL
(display inversion).
SIRIUS
Advertenties
Inhoudsopgave
