Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
SETTING THE ALARM
The alarm can only be set when the radio is in standby mode. If no buttons are pressed for 5 seconds, the radio will exit the alarm
setup and the setting is cancelled.
Setting the alarm clock
1.
Press the MENU button for about 3 seconds, and then press the MENU button again until the display shows "ALARM SET".
2.
Press the SELECT/INFO button to enter and the hour digits flash on the display.
3.
Press the Tuning Down or Tuning Up button to set the hour.
4.
Press the SELECT/INFO button to confirm. The minute digits flash.
5.
Press the Tuning Down or Tuning Up button to set the minute.
6.
Press the SELECT/INFO button to confirm.
7.
The display will then show "ALARM SOURCE". You may choose either "BUZZER" or "FM RADIO". Press the Tuning Down or
Tuning Up button to select. If "FM RADIO" is selected, the last listened station will be played when the alarm rings.
8.
Press the SELECT/INFO button to confirm.
9.
The display will then show "VOL XX". Press the Tuning Down or Tuning Up button to change the alarm volume.
10. Press the SELECT/INFO button to confirm.
Switching on/ off the alarm
1.
To switch the alarm on, press the SELECT/INFO button and hold for 2 seconds. The alarm icon will be shown at the top left
corner. To switch the alarm off, press the SELECT/INFO button again and hold for 2 seconds . The alarm icon will be disappear.
2. To turn off the alarm when it buzzes, simply press the On/Off button.
VOLUME & SOUND
To adjust the volume, simply press the Volume Down or Volume Up button when playing the FM radio or in AUX IN mode. The
level of volume (from 00 to 40 the loudest) will be shown on the LCD Display.
Note: When playing on batteries; if the energy level of the batteries is too low, sound will distort on higher volume.
360 DEGREES SOUND
The unique Neodymium speaker located on top of the radio provides a 360 degrees sound image. Suggestion: If preferred, place the
radio in a corner or close to a wall for additional sound reflection.
11
BACKLIGHT
LCD backlight configuration
1.
Press the On/Off button to turn on the radio.
2.
Press the MENU button until the display shows "BACKLIGHT".
3.
Press the SELECT/INFO button to enter backlight setup menu.
4.
Press the Tuning Down or Tuning Up buttons to select "on" in order to keep backlight always lightened when the radio is
turned on with AC power supply;
5.
Or to press the Tuning Down or Tuning Up buttons to select "off" (by default) so that the backlight will be lightened for about
10 seconds whenever a button was pressed with AC power supply.
6.
Press the SELECT/INFO button to confirm your choice. The LCD backlight will change upon the latest selection.
Note: The LCD backlight options "on" would only be functional when the radio was powered by AC power supply. In this case, when
the radio was powered by battery power supply, the LCD backlight would be switched to option "off" – 10 seconds lightened when a
button was pressed. When the radio was connected to mains again with AC power supplied, the last user settings would be applied
again.
KEY LOCK
The radio supports Key Lock function in all the Standby, FM and Aux-in modes.
1.
Pressed and hold SOURCE button for about 3 seconds, the LCD will display "Locked".
2. When keys are locked, the functions of the radio will be temporary disabled until it has been unlocked. During this moment, the
radio would only brighten the backlight for a few seconds and showing "Locked" in display.
3.
Pressed and hold the SOURCE button for 3 seconds again, the radio would display "Unlocked", and the key lock function will
be disabled.
Noted: When the radio is in standby and powered by batteries, some of the buttons were not be able to brighten the radio's backlight
in order to save energy.
GB
G B
12
Advertenties
Hoofdstukken
Inhoudsopgave
