Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Outdoor Receiver + Remote Control
User manual
Thank you for purchasing the Lightpro Outdoor receiver +
Remote control.
This document contains the required information for
correct, efficient and safe use of the product. Consult the
user manual of your transformer for more information
about the installation and connection of your lighting
plan or visit our website www.lightpro.nl
Read the information in this manual carefully before
using the product. Keep this manual near the product for
consultation in the future.
SPECIFICATIONS
Product
Article number
Dimensions Remote
Dimensions Receiver
Protection class
Ambient temperature
Input
PACKAGING CONTENT
1. Outdoor receiver + Remote control.
2. Screws
3. Plugs
4. Wall mount
5. Lightpro connector 137A
6. Connector 138A
7. Connector 173A
Check if all parts are present in the packaging. For
questions about parts, service, and any complaints or
other remarks, you can always contact us.
E-mail: info@lightpro.nl.
INSTALLATION
• This product should be used for 12V AC/DC
applications only.
• The receiver can be installed indoors and outdoors
(IP44).
• The remote control is for indoor use (IP20).
• The receiver can be operated with the remote control
from a maximum distance of 40 metres in an open
field.
• A maximum of 150W can be connected in an unlimited
amount of 12V AC/DC applications.
• The distance between receivers should be at least 0.5m.
• Place receiver at a height of 1 meter for optimum
reception (minimum height 0.5m).
12
Outdoor receiver +
Remote control.
166A / 167A
(H x Ø) 38 x 85 mm
(H x W x D) 45 x 70 x 88 mm
IP44 / IP20
-20 °C to 50 °C
12V AC/DC Max: 150W
PLACING BATTERIES IN REMOTE CONTROL (166A)
Insert 2 AAA batteries in the remote control as indicated
on page 4.
CONNECTING THE RECEIVER
(Page 5)
1. The receiver can be placed anywhere in the 12V system
to serve all 12V applications behind the receiver.
2. Remove the transformer plug from the power point.
3. Connect the receiver cable (1) to the 12V transformer or
(main) cable.
4. Connect the 12V applications or (main) cable to the
output connector of the receiver (4).
5. Insert the transformer plug in the power point.
PROGRAMMING REMOTE CONTROL AND RECEIVERS
1. Press the programming button on the receiver (2) and
hold it down for 5 seconds. The red indicator light on
the receiver will start to flash (3).
2. Press the group switch button (5) on the remote control
where the receiver needs to be programmed. The
indicator light (3) on the receiver stops flashing. The
receiver has now been programmed under the number
of this group switch button.
3. Multiple receivers can be programmed under 1
group switch button. Up to 9 groups can be served
independently.
4. The main switch button (6) on the remote control
switches all receivers on or off at the same time.
5. The indicator light ring (7) on the remote control shows
whether you switch applications on or off. When you
switch a receiver on, the indicator light ring flashes
once; when you switch an application off, the light ring
flashes twice.
6. When you switch a receiver on, the indicator light (3)
on the receiver will be on; when you switch a receiver
off, the indicator light on the receiver will go out.
7. To clear the receiver settings, press the programming
button on the receiver (2) and hold it down for 15
seconds. The indicator light (3) will flash for 15 seconds.
Once the light goes out, all settings will have been
cleared.
The remote control and receivers should work now. If not,
do the following:
• Check whether the remote control batteries have been
inserted correctly.
• Replace dead batteries in remote control.
• Check / test transformer continuity
• Check plug connections. Check the cable for an open
circuit.
Advertenties
Inhoudsopgave
