Fitting And Changing The Gas Cylinder; General Maintenance - Cadac MERIDIAN 3 Handleiding
Verberg thumbnails
Zie ook voor MERIDIAN 3:
- Installatie- en gebruikersinstructies (6 pagina's) ,
- Gebruiksaanwijzing (6 pagina's) ,
- Gebruikershandleiding (6 pagina's)
Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
• Manual ignition: To light the burners manually, fi rst remove the cast iron grill plate and
the defl ector plate directly underneath it. Ignite a match or fi relighter and position it next
to the left hand burner. Turn on the gas supply to that burner only by pushing the control
valve in and turning it in an anti-clockwise direction. This will ignite the burner. Once the
burner is ignited, carefully replace the defl ector plate and cast iron grill plate. You will now
be able to light the remainder of the burners as described in 'Cross lighting' above.
• Use the control knobs to adjust the individual burner fl ame intensity to the desired level by
turning the knob anti-clockwise to decrease the fl ame and clockwise to increase it.
• After use, fi rst close the valve on the gas cylinder. When the fl ame is extinguished, close
the burner control valves on the appliance by turning control knobs fully clockwise.
4. Fitting and Changing the Gas Cylinder
• Before connecting the appliance to a gas cylinder, ensure that the rubber seal on the
regulator is in position and in good condition.
• Carry out this check each time you fi t the appliance to a gas cylinder.
• Blow out any dust from the cylinder opening to prevent possible blockage of the jet.
• Ensure that the appliance valves are in the off position by turning the knobs fully clockwise
to their stop.
• Ensure that the gas cylinder is fi tted or changed in a well-ventilated location, preferably
outdoors, away from any source of
people.
• Make sure that the gas cylinder is kept upright at all times. Hand tighten the regulator onto
the cylinder until it is fully engaged.
• If there is a leak on your appliance (smell of gas), extinguish all sources of ignition in the vicinity of the appliance. If you wish to check
for leaks on your appliance, use soapy water which is applied to the suspected area. A formation of bubbles will indicate a gas leak.
Check that all the connections are securely fi tted and re-check with soapy water. If you cannot rectify the gas leak, do not use the
appliance. Contact your local CADAC stockist for assistance.
• When changing a gas cylinder, fi rst close the cylinder valve and then the appliance valve, making sure the fl ame is extinguished and
unscrew the regulator. Re-fi t the regulator to a full cylinder following the same precautions as described above.
• After the appliance has been fully assembled, perform a gas leak test before operating the appliance.
• Make sure that the gas cylinder is kept upright at all times. Hand tighten the regulator onto the cylinder until it is fully engaged.
• If there is a leak on your appliance (smell of gas), extinguish all sources of ignition in the vicinity of the appliance. If you wish to check
for leaks on your appliance, use soapy water which is applied to the suspected area. A formation of bubbles will indicate a gas leak.
Check that all the connections are securely fi tted and re-check with soapy water. If you cannot rectify the gas leak, do not use the
appliance. Contact your local CADAC stockist for assistance.
• When changing a gas cylinder, fi rst close the cylinder valve and then the appliance valve, making sure the fl ame is extinguished and
unscrew the regulator. Re-fi t the regulator to a full cylinder following the same precautions as described above.
• After the appliance has been fully assembled, perform a gas leak test before operating the appliance.
5. General Maintenance
• There are no predetermined maintenance intervals for this appliance.
• It is dangerous to use an appliance with a cracked or perished seal and/or hose. Inspect both seals and hose regularly and replace if
they are not in order before using the appliance.
• If the appliance was in use it will be hot. Allow to cool suffi ciently before attempting any maintenance.
• CADAC Patio BBQ's are fi tted with specifi c CADAC jets to regulate the correct amount of gas. Should the hole in the jet become
blocked this may result in a small fl ame or no fl ame at all. Do not attempt to clean the Jet with a pin or other such device as this may
damage the orifi ce, which could make the appliance unsafe. Refer to Table 1 for jet sizes.
Replacing a blocked jet
• Ensure that the cylinder valve is closed, then disconnect the appliance from the gas cylinder.
• Remove the grill plates. Remove the fl ame tamers to expose the burners. Remove the retaining screws of the affected burner.
• Remove the affected burner by lifting it out of its location taking care not to damage the control valve whilst doing so. This will expose
the jet.
• Unscrew the blocked Jet with a suitable spanner and replace it with a new Jet. Do not use pliers on the Jet as they can cause damage,
making the Jet unusable or impossible to remove.
• Do not over tighten as this may damage the Jet. To re-assemble, reverse the above procedure.
503-0479 LEV5 - (982231, 982241) - Meridian BIB 2016-2017 (VanWard) User Manual 28mbar (EU+SA).indd 3
ignition, such as naked fl ames and away from other
3 3
GB
19/12/2016 14:15:07
Advertenties
Inhoudsopgave
