Inhoudsopgave
Advertenties
duct Maintenance
Cleaning Side Brushes
Clean the side brush when it become dirty and replace it if it's damaged. The maximum life span of
de Brushes
ning Side Brushes
the side brush is 12 months.
Clean the side brush when it become dirty and replace it if it's damaged. The maximum life span of
Note: Before replacing side brushes, check and ensure that the L/R mark on the side brush match
the side brush is 12 months.
Charging without a charging station
rush when it become dirty and replace it if it's damaged. The maximum life span of
he side brush when it become dirty and replace it if it's damaged. The maximum life span of
with the L/R mark on the bottom base of the robot.
Plug the adapter into the contact and insert the DC input into
Note: Before replacing side brushes, check and ensure that the L/R mark on the side brush match
12 months.
e brush is 12 months.
de Brushes
the vacuum.
with the L/R mark on the bottom base of the robot.
Cleaning Dust Bin and Filters
While charging:
lacing side brushes, check and ensure that the L/R mark on the side brush match
·
efore replacing side brushes, check and ensure that the L/R mark on the side brush match
Cleaning Dust Bin and Filters
ush when it become dirty and replace it if it's damaged. The maximum life span of
Display shows flashing '1111': vacuum is charging
·
k on the bottom base of the robot.
e L/R mark on the bottom base of the robot.
Empty and clean the dust bin after each usage following the steps as show in the figures below:
·
Display shows 'FULL': device is fully charged
12 months.
Empty and clean the dust bin after each usage following the steps as show in the figures below:
st Bin and Filters
ning Dust Bin and Filters
·
Display shows 'Erro': the power switch must be on to
acing side brushes, check and ensure that the L/R mark on the side brush match
charge
k on the bottom base of the robot.
the dust bin after each usage following the steps as show in the figures below:
and clean the dust bin after each usage following the steps as show in the figures below:
CLEANING AND MAINTENANCE
st Bin and Filters
CLEANING OUT THE CANISTER AND FILTER
the dust bin after each usage following the steps as show in the figures below:
Clean the canister and the filter after each use in the following manner:
1
A. Hold the bottom of dust bin, and press down on the button using your
A. Hold the bottom of dust bin, and press down on the button using your
thumb to take out of the dust bin.
thumb to take out of the dust bin.
m of dust bin, and press down on the button using your
d the bottom of dust bin, and press down on the button using your
ut of the dust bin.
to take out of the dust bin.
m of dust bin, and press down on the button using your
3
t of the dust bin.
C. After press down button
C. After press down button
and o
pen dust bin upper cover
and o
pen dust bin upper cover
5
D. Open dust bin cover and take out the
down button
er press down button
primary filter and HEPA filter.
D. Open dust bin cover and take out the
n upper cover
en dust bin upper cover
down button
primary filter and HEPA filter.
upper cover
F. Wash the dust bin and primary filter under tap water,
F. Wash the dust bin and primary filter under tap water,
clean the HEPA filter with brush, avoid washing it under
clean the HEPA filter with brush, avoid washing it under
1.
Press the button that opens the canister. Remove the canister from the vacuum.
water.
water.
2.
Press the open button to open the canister.
Remove the HEPA filter, including the holder, from the canister.
3.
4.
Empty the canister into the waste bin.
bin and primary filter under tap water,
h the dust bin and primary filter under tap water,
Rinse the canister and filter holder under running water. Let them dry before putting them back in
5.
bin and primary filter under tap water,
ter with brush, avoid washing it under
he HEPA filter with brush, avoid washing it under
place. Clean the HEPA filter with the dust brush.
ter with brush, avoid washing it under
If the HEPA filter is dirty, after about 30 days of use, you can also clean it under running water. Let
·
it dry before putting it back in place.
The HEPA filter must be replaced after frequent use. The maximum service life of the filter is
·
approximately 6 months.
40
DO7293S
D. Open dust bin cover and take out the
D. Open dust bin cover and take out the
primary filter and HEPA filter.
primary filter and HEPA filter.
D. Open dust bin cover and take out the
primary filter and HEPA filter.
G. Assemble primary filter and HEPA filter again into
G. Assemble primary filter and HEPA filter again into
G. Assemble primary filter and HEPA filter again into
dust bin.
dust bin.
dust bin.
16
16
16
Clean the side brush when it become dirty and replac
the side brush is 12 months.
Note: Before replacing side brushes, check and ensu
with the L/R mark on the bottom base of the robot.
Cleaning Dust Bin and Filters
Empty and clean the dust bin after each usage follow
A. Hold the bottom of dust bin, and press down on the bu
thumb to take out of the dust bin.
2
B. Take out dust bin.
B. Take out dust bin.
B. Take out dust bin.
4
C. After press down button
and o
pen dust bin upper cover
6
E. Empty the dust bin.
E. Empty the dust bin.
F. Wash the dust bin and primary filter under tap water,
E. Empty the dust bin.
clean the HEPA filter with brush, avoid washing it under
water.
G. Assemble primary filter and HEPA filter again into
G. Assemble primary filter and HEPA filter again into
dust bin.
dust bin.
16
16
B. Take out dust bin.
B. Take out dust bin.
D. Open dust bin cover
primary filter and HEPA
E. Empty the dust bin.
E. Empty the dust bin.
10
G.
du
16
Advertenties
Inhoudsopgave
