Advertenties
entered remains stored. The search stops after
approx. 30 seconds of inactivity.
Automatic code search
Your remote control finds the correct settings
almost automatically in seconds:
1.
Switch on the appliance to be
controlled. A channel number, for example,
appears in the display of your satellite receiver.
2.
To start the code search, press the
required appliance button, e.g.
3.
Then press
SET
seconds until the lamp (LED) starts to blink.
4.
Then point the remote control at the
appliance to be controlled while the remote
control emits a different ON/OFF signal every
second.
5.
When your appliance reacts, press
SET within 1-2 seconds, to end the search. – If
you ended the search too late, continue to
search using the Manual Code Search (see
above).
6.
Finally, test the control code setting
by trying to control, for example, your DVD
appliance. If it does not work correctly, please
try the code search again. The code search
then begins with the next code in the
sequence.
-
Remember
to
appliance, e.g. DVD, back on again if you wish
to continue searching.
Code identification
You can read off the 3-digit codes you have set
at any time:
1.
Press the appliance button of the
appliance which code you want to read off, e.g.
TV1.
2.
Press the
button and 1,2,3,
SET
depending on the part of the code you want to
read off. For example, if you press
TV and the code 176 (in this example) has
been set, the lamp blinks once after SET+1 is
released to show that the hundred figure is 1.
All you have to do is count. The ten figure is
indicated after
+ is released, e.g. it blinks
SET 2
7 times for the 7 in 176. The one figure is
indicated after
+ is released, e.g. it blinks
SET 3
6 times for the 6 in 176.
Learning, Programming, of Missing Control
Functions
The LEARN function is used to supplement the
preprogrammed codes. The standard code
may provide most of functions needed, but you
may miss some key functions. Or you didn´t
find any functioning preprogrammed code for a
device. You can capture upto 65 key function
codes, max 40 per device. The last captured
function will overwrite the previous. learnt.
Vivanco GmbH, D-22926 Ahrensburg, E-Mail
UR 14 UNIVERSAL CONTROLLER
1
For learning of key codes you must use a
functioning orginal remote controller. Please
use fresh batteries for both remote controls.
2
Please point the original´s remote control
transmitter LED towards the receiver LED of
UR 14 (placed on top, same as transmitter
LED). Distance of LEDs between both remotes
shall be approximately 10mm and must be in
straight line of sight. – Sometimes you have to
move the remotes a bit too and fro while
*) briefly.
TV1
learning, in order to find right positions.
for about 5
3
Press the LEARN key for about 3
seconds until the LED (lamp) turns on.
4
Within 10 seconds press a device key
(e.g.
DVD1)
time .
5
Press and release the target key on the
UR 14, that you want to learn
(e.g. POWER), the LED starts flashing.
6
Press and hold the source key on the
original remote control (e.g. POWER) until the
LED
on your UR 14 remote control stops
flashing and changes to on again. That
indicates that a new function code, e.g.
POWER, has been learnt.
7
Repeat steps 4 to 6 to for capturing more
key functions. - If there is a learning(capturing)
switch
your
problem, the LED blinks 2 times, lights up for
10 seconds. Then repeat steps 4 to 6 for
capturing more keys functions.
8
Press and release
learning mode. – The controller will exit the
learning mode automatically after about 30
seconds of inactivity.
**) Learning is possible for items, which can be
controlled by using device buttons TV1, TV3,
CD, CBL only!
Memory full indication: if the memory is full,
+ after
SET 1
the LED blinks 2 times and then a programmed
key can be overitten or the controller will exit
learnning mode after 10 seconds of idleness.
Reset/deletion of a captured key function
1
Press the
seconds until the LED (lamp) turns on.
2
Press and hold the device button, e.g.
DVD1, which belongs to the to be deleted key
function. The LED will flash once.
3
Press the key of which the captured
function shall be deleted, e.g.
briefly. The LED will flash once and the learnt
code is deleted.
4
Press and release
deletion mode.
Reset/deletion of all captured key functions
for a device:
1
Press the
seconds until the LED (lamp) turns on.
:
hotline@vivanco.de
**) briefly. The LED is flashing one
(to reprogram)
key for exit of
LEARN
key for about 3
LEARN
, additionally
3
key for exit of
LEARN
key for about 3
LEARN
, Helpline: +49 (0) 4102 231135
3
Advertenties
