Inhoudsopgave
Advertenties
Operating mode S6 40%: Continuous operation
with idling (cycle time 10 minutes). To ensure that
the motor does not become excessively hot, it
may only be operated for 40% of the cycle at the
specifi ed rating and must then be allowed to idle
for 60% of the cycle.
Danger!
Sound
Sound values were measured in accordance with
EN 62841.
L
sound pressure level ..................... 82,7 dB(A)
pA
K
uncertainty ............................................. 3 dB
pA
L
sound power level ....................... 95,7 dB(A)
WA
K
uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
Warning:
The noise emission levels may vary from the level
specifi ed during actual use, depending on the
way in which the power tool is used, especially
the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
Anl_H_DS_150_SPK7.indb 16
Anl_H_DS_150_SPK7.indb 16
GB
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Pull the power plug before doing any mainte-
nance or assembly work on the equipment.
•
The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a
work bench or similar.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the grinding wheel to
run freely.
•
Check that the voltage on the rating plate is
the same as your supply voltage before you
connect the machine to the power supply.
5.1 Assembling the spark defl ector / safety
window (Fig. 3/4)
•
Fit the spark deflector (3) to the double wheel
grinder using the adjusting screw (10) (Fig. 3).
•
Fit the safety window (2) to the spark deflec-
tor (3) using the adjusting screw (11) (Fig. 4).
5.2 Adjusting the spark refl ector
(Fig. 5 / Item 3)
•
Adjust the spark deflector (3) using the adjus-
ting screw (10) so that the distance between
the dry grinding wheel (5) and the spark de-
flector (3) is as small as possible and certain-
ly does not exceed 2 mm.
•
Adjust the spark deflector (3) periodically to
compensate for wear on the wheel.
5.3 Assembling the workpiece supports (Fig.
6)
Screw the workpiece supports (7) to the double
wheel grinder using the star screw (6) and the
- 16 -
29.06.2023 07:46:58
29.06.2023 07:46:58
Advertenties
Inhoudsopgave
