Inhoudsopgave
Advertenties
CAUTION!
All checks and repairs should be carried out by
the supplier's service department or by service
site certified by the supplier. All checks and repairs must
be carried out only when rubber hose is disconnected
from the gas cylinder. Cut off gas supply before
disconnecting the hose!
CAUTION!
Do not pull the rubber hose to move or lift gas
container.
Check condition of rubber hose each time before
starting work. In case any damage is found (accidental
surface cut, signs of burns, bulge or change of diameter)
immediately replace the hose with a new one.
Rubber hose also must be replaced not later than 5
years from its production date specified on the hose.
1
2
1.
Read the manual, observe the warnings and safety
conditions contained in it!
2.
Outdoor tool.
3.
Attention! Hot surfaces.
4.
Keep children away from the tool.
TECHNICAL PARAMETERS
Flame temperature [°C]
Gas consumption [g/h]
Burner power [kW]
Number of burners
Burner diameter (mm)
Type of burner
Hose length
Additional equipment
TORCH COMPONENTS
a.
Burner
b. Handle
c.
Gas valve wheel
d. Rubber hose
e.
Keys
f.
Gas valve lever
g. Stiff connection
OPERATION AND USE
Starting the torch
– Release gas valve lever
– Turn gas valve of the torch towards (-) to turn it off.
– Connect gas hose to the torch and gas container.
– Open gas container valve to supply rubber hose with
gas.
TOPEX.PL
3
4
1850
4000
58
1
W
=73, W
=86
1
2
roofing
5m
60 cm gas supply stiff
connection
– Direct the torch nozzle forward.
– Press the gas valve lever against the handle
– Turn the torch gas valve by 2/3 of a turn in (+)
direction (you should hear specific hissing of the gas
coming out).
– Light up gas coming out of the burner.
Adjusting flame size and temperature
Gas valve wheel allows setting the flame size and
temperature.
Turn the wheel in (-) direction to reduce the flame size
and temperature. Turn the wheel in (+) direction to
increase the flame size and temperature.
Extinguishing the flame
– Release gas valve lever
– Turn the gas valve in (-) direction to extreme position.
– Cut off gas supply from the gas container when the
flame is extinguished.
MAINTENANCE
Sometimes using contaminated gas that may
appear when the gas tank is almost empty
causes partial clogging of the nozzle. To clean the nozzle
turn the gas container valve off, disconnect rubber hose
from the gas container, disassemble the torch, clean the
nozzle thoroughly with petrol or similar liquid. You can
also use very thin wire to clear the nozzle. UNDER NO
CIRCUMSTANCES ALLOW THE NOZZLE OPENING TO
ENLARGE.
RU
ГАЗОВАЯ ГОРЕЛКА ДЛЯ КРОВЕЛЬНЫХ
РАБОТ (НА СЖИЖЕННОМ ГАЗЕ) 44E122
ПРАВИЛА ТЕХНИКИ БЕЗОПАСНОСТИ
Паяльник не оснащен индикатором температуры.
Неаккуратное
обращение
может стать причиной пожара. Берегите себя и
окружающую среду, соблюдая необходимые меры
безопасности.
ВНИМАНИЕ!
1.
Не приближайте сопло горелки к лицу и рукам.
Это может причинить ожоги.
2.
Во время работы с горелкой сопло сильно нагревается.
Высокая температура сохраняется в течение
некоторого времени после завершения работы.
3.
Запрещается приближать нагретое сопло горелки
к легковоспламеняющимся материалам.
с
инструментом
5
Advertenties
Inhoudsopgave
