Delivery Content | Levering Inhoud | Levering Indhold Leverans Innehåll | Содержание доставки 1 x PoolLab 1.0 ® 1 x Light shield 3 x AAA Batteries 1 x Crushing | Stirring Rods 1 x 10ml syringe 1 x User guide 20 x Phenol Red Photometer tablets 20 x DPD N°...
Switch on | Inschakelen | Tænd | Slå på | Включить 00:02 ZERO On/Off button can also be used to skip countdown during measurement (not recommended) De On/Off knop kan ook gebruikt worden om het aftellen tijdens de meting af te breken (dit wordt niet aanbevolen) On/Off kan også...
Advices | Adviezen | Rådgivning | Råd | Советы PHOTOMETER RAPID Always use PHOTOMETER grade tablets! Never use RAPID grade tablets! Do not touch reagent tablets! Gebruik altijd FOTOMETER kwaliteit tabletten! Gebruik nooit RAPID tabletten! Raak geen reagens tabletten aan! Brug altid tabletter af PHOTOMETER-kvalitet! Brug aldrig tabletter af RAPID-kvalitet! Rør ikke ved reagenstabletter! Använd alltid tabletter av PHOTOMETER-kvalitet! Använd aldrig...
Pagina 8
IMPORTANT | BELANGRIJK | VIGTIGT | VIKTIGT | ВАЖНО Detergent waterproof (IP68 ) ZERO It is important to clean the device after each measurement to get rid of any reagent residues! Please ensure that the cuvette has been cleaned before each measurement (e.g. under clear water/or simply rinsing the cuvette in the pool is sufficient as long as no residues remain).
Pagina 9
Важно очищать прибор после каждого измерения, чтобы избавиться от остатков реагентов! Пожалуйста, убедитесь, что кювета была очищена перед каждым измерением (например, под чистой водой или просто ополосните кювету в бассейне, если не осталось никаких остатков). Do not leave the device in the sun! Laat het apparaat niet in de zon liggen! Lad ikke apparatet ligge i solen! Lämna inte apparaten i solen!
Tablet Mode: Press And Hold ZERO + Power Button ZERO ZERO ZERO Liquid Mode: Press And Hold ZERO + Power Button ZERO ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 12
From firmware version 72 onwards, you have the option of measuring the following parameters with tablets as well as with liquid reagents: pH, chlorine, chlorine dioxide, ozone and bromine. You can choose between two measurement settings in the unit: Tablets and Liquid reagents. You can switch between the modes by pressing and releasing the ZERO &...
Pagina 13
Från och med version 72 av firmware har du möjlighet att mäta följande parametrar med tabletter och flytande reagenser: pH, klor, klordioxid, ozon och brom. Du kan välja mellan två mätinställningar i enheten: Tabletter och flytande reagenser. Du kan växla mellan lägena genom att samtidigt trycka på och släppa knappen ZERO &...
QUICK START GUIDE SNELSTARTGIDS HURTIGSTARTVEJLEDNING SNABBSTARTGUIDE КРАТКОЕ РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ Scan the QR-code to watch our intstruction video info@spafix.dk www.spafix.dk...
Pagina 15
Hold & Press To Switch On 3 x AAA 00:02 ZERO START: Take 10 ml Water Sample 10 ml No Reagents! waterproof (IP68 ) ZERO Put On Lightshield ZERO ZERO ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 16
Remove Lightshield Reagent(s) For Your Test (Refer To Chapter In Manual) ZERO ZERO Put On Lightshield Use Force! ZERO ZERO Completely Dissolved Residue Shortcut Await For Your Countdown Test (Refer To Chapter In Manual) ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 17
Empty & Clean For Next Test: Take 10ml waterproof (IP68 ) ZERO 10 ml *If Device Was Not Switched *If Device Was Switched Off, Off, Start From Step 8 Start From Step 3 End Of Quick Start Guide | Einde van de snelstartgids | Slutning af kvikstartvejledning | Slutet av guiden för snabbstart | Конец...
ZERO waterproof (IP68 ) ZERO Take 10 ml Water Sample 10 ml No Reagents! waterproof (IP68 ) ZERO ZERO ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 19
Only 1 Time Per Test Batch | Slechts 1 keer per testbatch Kun 1 gang pr. testbatch | Endast 1 gång per testbatch Только 1 раз для каждой тестовой партии The "ZERO" step (page 18) is only necessary once after switching on. Make sure that the water to be measured does not (!) contain any tablet/reagent in the cuvette and that the light protection cover is in place.
Active Oxygen Actieve zuurstof Aktivt ilt Aktiv syre Активный кислород (MPS) 0.0 – 30.0 ppm (mg/l) DPD N°4 Photometer* 10.0 30.0 *not part of standard equipment waterproof (IP68 ) ZERO Take 10 ml Water Sample waterproof (IP68 ) 10 ml ZERO info@spafix.dk www.spafix.dk...
Pagina 21
1 x DPD N°4 Use Force! Photometer* ZERO! (p.18) Completely Dissolved ZERO ZERO ZERO Residue ZERO ZERO info@spafix.dk www.spafix.dk...
Alkalinity Alkaliteit Alkalinitet Щелочность 0 – 200 ppm (mg/l) CaCO₃ Alkalinity–M Photometer waterproof (IP68 ) ZERO Take 10 ml Water Sample waterproof (IP68 ) 10 ml ZERO info@spafix.dk www.spafix.dk...
Pagina 23
Use Force! 1 x Alkalinity-M ZERO! (p.18) Photometer Completely Dissolved ZERO ZERO ZERO Residue ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 25
Only if your water sample does contain Chlorine next to Bromine (both disinfectants used), the following procedure "A" needs to be followed and Glycine* reagent needs to be used. Otherwise (only Bromine present), please follow procedure "B". Alleen als uw watermonster naast broom ook chloor bevat (beide ontsmettingsmiddelen gebruikt), moet de volgende procedure "A"...
Pagina 26
With Chlorine | Met chloor | Med klor | С хлором Glycine* Use Force! Completely dissolved ZERO ZERO Residue Tablet Or Liquid? (p. 10) DPD N°1 Photometer Use Force! DPD 1A + DPD 1B Completely dissolved ZERO ZERO Residue info@spafix.dk www.spafix.dk...
Pagina 27
Without Chlorine | Zonder chloor Uden klor | Utan klor | Без хлора Tablet Or Liquid? (p. 10) DPD N°1 Photometer DPD 1A + Use Force! DPD 1B Completely Dissolved ZERO ZERO Residue 8 /6 ZERO ZERO info@spafix.dk www.spafix.dk...
Calcium Hardness Calciumhardheid Calciumhårdhed Kalciumhårdhet Твердость кальция 0 – 500 ppm (mg/l) CaCO₃ POL20CaH1 | POL20CaH2 *not part of standard equipment waterproof (IP68 ) ZERO ZERO ZERO! Take 10 ml Water Sample (p.18) waterproof (IP68 ) 10 ml ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 29
POL20CaH1* POL20CaH2* *Shake Before Use! 10 x 10 x ZERO ZERO ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 30
ZERO ZERO ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 33
Tablet Or Liquid? (p. 10) DPD N°1 Photometer DPD 1A + ZERO! (p.18) DPD 1B ZERO ZERO Use Force! Completely Dissolved ZERO ZERO Residue info@spafix.dk www.spafix.dk...
Pagina 34
Tablet Or Liquid? (p. 10) DPD N°3 Photometer DPD 3C ZERO ZERO ppm = mg/l Use force! Completely Dissolved ZERO ZERO Residue info@spafix.dk www.spafix.dk...
Pagina 35
ZERO Total Chlorine is measured directly after free Chlorine without emptying the cuvette. The DPD 3 tablet is added to the sample water which already contains the DPD 1 tablet (dissolved). Combined Chlorine is calculated as Total Chlorine minus free Chlorine. The free chlorine measurement must be taken within 1 minute after dissolving the tablet.
Pagina 36
Samlet klor måles direkte efter frit klor uden at tømme kuvetten. DPD 3-tabletten tilsættes til prøvevandet, som allerede indeholder DPD 1-tabletten (opløst). Kombineret klor beregnes som samlet klor minus frit klor. Målingen af frit klor skal foretages inden for 1 minut efter opløsningen af tabletten.
Pagina 39
Only if your water sample does contain Chlorine next to Chlorine Dioxide (both disinfectants used), the following procedure "A" needs to be followed and Glycine* reagent needs to be used. Otherwise (only Chlorine Dioxide present), please follow procedure "B". Alleen als uw watermonster naast Chloordioxide ook Chloor bevat (beide ontsmettingsmiddelen gebruikt), moet de volgende procedure "A"...
Pagina 40
With Chlorine | Met chloor | Med klor | С хлором Glycine* Use Force! Completely Dissolved ZERO ZERO Residue Tablet Or Liquid? (p. 10) DPD N°1 Photometer Use Force! DPD 1A + DPD 1B Completely Dissolved ZERO ZERO Residue info@spafix.dk www.spafix.dk...
Pagina 41
Without Chlorine | Zonder chloor Uden klor | Utan klor | Без хлора Tablet Or Liquid? (p. 10) DPD N°1 Photometer Use Force! DPD 1A + DPD 1B Completely Dissolved ZERO ZERO Residue 8 /6 ZERO ZERO info@spafix.dk www.spafix.dk...
Cyanuric Acid Cyanuurzuur Cyanursyre Cyanursyra Циануровая кислота 0 – 160 ppm (mg/l) CYA–Test Photometer waterproof (IP68 ) ZERO ZERO ZERO! Take 10 ml Water Sample (p.18) waterproof (IP68 ) 10 ml ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 43
1 x CYA–Test Use Force! Photometer Completely Dissolved ZERO ZERO Residue ZERO ZERO info@spafix.dk www.spafix.dk...
(LR) Hydrogen Peroxide Waterstofperoxide Brintoverilte Väteperoxid Перекись водорода 0.00 – 2.90 ppm (mg/l) Hydr. Peroxide LR Photometer* 0.00 1.45 2.90 *not part of standard equipment waterproof (IP68 ) ZERO ZERO ZERO! Take 10 ml Water Sample (p.18) waterproof (IP68 ) 10 ml ZERO ZERO...
Pagina 45
1 x Hydr. Peroxide Use force! Photometer* completely dissolved ZERO ZERO residue ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 46
(HR) Hydrogen Peroxide Waterstofperoxide Brintoverilte Väteperoxid Перекись водорода 0 – 200 ppm (mg/l) Hydr. Peroxide HR Photometer | Acidifying PT *not part of standard equipment waterproof (IP68 ) ZERO ZERO Take 10 ml Water Sample ZERO! (p.18) waterproof (IP68 ) 10 ml ZERO ZERO...
Pagina 47
1 x Acidifying Use Force! ZERO ZERO Completely Residue Dissolved 1 x Hydr. Peroxide Photometer* Use Force! ZERO ZERO Completely Residue Dissolved ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 49
Only if your water sample does contain Ozone next to Chlorine (both disinfectants used), the following procedure "B" needs to be followed and Glycine* reagent needs to be used. Otherwise (only Ozone present), please follow procedure "A". Alleen als uw watermonster naast chloor ook ozon bevat (beide ontsmettingsmiddelen gebruikt), moet de volgende procedure "B"...
Pagina 50
Without Chlorine | Zonder chloor Uden klor | Utan klor | Без хлора Tablet Or Liquid? (p. 10) DPD N°1 + DPD N°3 Use Force! Photometer DPD 1A + DPD 1B + DPD 3C Completely Dissolved ZERO ZERO Residue ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 51
With Chlorine | Met chloor | Med klor | С хлором Tablet Or Liquid? (p. 10) DPD N°1 + DPD N°3 Use Force! Photometer DPD 1A + DPD 1B + Completely DPD 3C Dissolved ZERO ZERO Residue ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 52
With Chlorine | Met chloor | Med klor | С хлором 0 ml ZERO 10 ml waterproof (IP68 ) ZERO Glycine* Use Force! Completely Dissolved ZERO ZERO Residue info@spafix.dk www.spafix.dk...
Pagina 53
With Chlorine | Met chloor | Med klor | С хлором Tablet Or Liquid? (p. 10) DPD N°1 + DPD N°3 Use Force! Photometer DPD 1A + DPD 1B + Completely DPD 3C Dissolved ZERO ZERO Residue ZERO ZERO info@spafix.dk www.spafix.dk...
Liquid Mode: Tablet Mode: 6.50 – 8.40 pH 6.50 – 8.40 pH Phenol Red Liquid* Phenol Red Photometer *not part of standard equipment waterproof (IP68 ) ZERO Take 10 ml Water Sample waterproof (IP68 ) 10 ml ZERO info@spafix.dk www.spafix.dk...
Pagina 55
Tablet Or Liquid? (p. 10) Phenol Red Photometer ZERO! (p.18) Phenol ZERO ZERO Use Force! Completely Dissolved ZERO ZERO Residue info@spafix.dk www.spafix.dk...
Pagina 56
ZERO The Total Alkalinity value has to be minimum 50 mg/l to obtain a correct pH value. De totale alkaliteit moet minimaal 50 mg/l bedragen om een correcte pH-waarde te verkrijgen. Totalalkalinitetsværdien skal være på mindst 50 mg/l for at opnå en korrekt pH-værdi.
PHMB 5 – 60 ppm (mg/l) PHMB Photometer* *not part of standard equipment waterproof (IP68 ) ZERO ZERO ZERO! Take 10 ml Water Sample (p.18) waterproof (IP68 ) 10 ml ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 59
1 x PHMB Photometer Use Force! Completely Dissolved ZERO ZERO Residue ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 60
It is imperative that you clean the objects used for the measure- ment and come into contact with the sample water containing the reagent (cuvette, lid, stirring rod) thoroughly with a brush, water and then with distilled water, otherwise the measuring equipment may turn blue over time.
Total Hardness Totale Hardheid Samlet hårdhed Total hårdhet Общая жесткость 0 – 500 ppm (mg/l) CaCO₃ POL20TH1 | POL10TH2 *not part of standard equipment waterproof (IP68 ) ZERO ZERO Take 10 ml Water Sample ZERO! (p.18) waterproof (IP68 ) 10 ml ZERO ZERO info@spafix.dk...
Pagina 63
POL20TH1* POL10TH2* *Shake Before Use! 10 x ZERO ZERO ZERO ZERO info@spafix.dk www.spafix.dk...
Urea Ureum Мочевина 0.1 – 2.5 ppm (mg/l) Dechlor | PL Urea 1 | PL Urea 2 Ammonia N°1 | Ammonia N° 2 *not part of standard equipment waterproof (IP68 ) ZERO ZERO Take 10 ml Water Sample ZERO! (p.18) waterproof (IP68 ) 10 ml...
Pagina 65
1 x Dechlor ZERO ZERO Use Force! ZERO ZERO Completely Dissolved Residue PL Urea *Shake Before Use! ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 66
PL Urea *Shake Before Use! ZERO ZERO ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 67
4 14 Ammonia N°1 ZERO ZERO Ammonia N°2 ZERO ZERO info@spafix.dk www.spafix.dk...
Pagina 68
ZERO ZERO If the sample contains free chlorine, a „Dechlor“ tablet has to be added to the vial, before adding PL Urea 1 and PL Urea 2. Ammonia N° 1 only dissolves entirely after Ammonia N° 2 was added. Ammonia and chloramines will be detected together. The result displayed will show the sum of both.
Pagina 69
Hvis prøven indeholder frit klor, skal der tilsættes en "Dechlor"- tablet til hætteglasset, før PL Urea 1 og PL Urea 2 tilsættes. Ammoniak nr. 1 opløses først helt, når ammoniak nr. 2 er tilsat. Ammoniak og kloraminer påvises sammen. Det viste resultat viser summen af begge dele.
OR-UR (Dilution) | OR-UR (Verdunning) OR-UR (Fortynding) | OR-UR (Utspädning) | OR-UR (Разбавление) OR = Overrange / UR = Underrange. Test result is outside the range of the method. OR results can be brought into measurement range by dilution. Use syringe to take only 5ml (or 1ml) sample water plus 5ml (9ml) distilled water.
Error Codes | Foutcodes | Fejlkoder Felkoder | Коды ошибок Change batteries | Batterijen vervangen | Skift batterier BAT!: | Byt batterier | Замените батарейки Err02: (Too dark) Clean measurement chamber or dilute sample | (Te donker) Meetkamer reinigen of monster verdunnen | (For mørk) Rengør målekammeret eller f o r t y n d i n g a f p r ø...
Troubleshooting | Fehlerbehebung | Soluc. Problemas | Dépannage | Risoluzione Die Problemi 1) 01.01.1970: The date on the PoolLab 1.0 is set to 01.01.1970 when ® delivered, after each battery change and after each update. Please reconnect to the LabCOM app so that the smartphone date is adopted again.
Pagina 73
1) 01.01.1970: Datumet på PoolLab 1.0® är inställt på 01.01.1970 vid leverans, efter varje batteribyte och efter varje uppdatering. Vänligen anslut dig på nytt till LabCOM-appen så att datumet för smarttelefonen antas igen. 2) Idealvärden: Kontakta leverantören av din poolkemi för att fråga efter idealvärden för din pool. 3) Repad kuvett: Så...
Changing The Cuvette | De Cuvette verwisselen | Udskiftning af kuvette | Byte av kyvett | Замена кюветы 90° ZERO ZERO 90° ZERO ZERO info@spafix.dk www.spafix.dk...
Technical Data | Technische gegevens | Tekniske data Tekniska data | Технические данные www.poollab.org MSDS msds.water-id.com Cloud labcom.cloud 530 nm / 570 nm / 620 nm LED: 3 x AAA (1.5 V, LR03) 300 sec. ï 5 - 45°C IP 68 (1 h / 1.2 m) Developed in Germany Produced in PRC info@spafix.dk...
Disposal | Verwijdering Bortskaffelse | Bortskaffande | Утилизация Device According to EC Directive 2002/ 96/EC, electronic devices must not be disposed of in normal domestic waste. The manu-facturer of this device, Water-i.d.® GmbH, Daimlerstr. 20, D-76344 Eggenstein will dispose of your PoolLab Photometer free of charge (not including costs of sending the device to us).
UKCA Complaince Statement UK Conformity Assessed We, Water-i.d. GmbH Germany, hereby certify our responsibility, that the following product: PrimeLab 2.0 Photometer, is tested to and conforms with the essential test suites included in the following standards, which are in force within the UK: Standards Legislation Number Regulations 2016 (S.I.
Pagina 85
FCC Part 15 Compliance Statement IC Licence-Exempt RSS Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Pagina 86
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device complies with Industry Canada's RSS for licence-exempt radio equipment. Operation is permitted under the following two conditions: (1) this device may not cause interference, and (2) the user of this device must accept any radio interference received, even if the interference is likely to affect the operation of the device.
Certificate | Certificaat | Certifikat Certifikat | Сертификат Certificate Of Compliance We hereby certify that the device PoolLab 1.0 ® With it‘s serial number as stated below, has passed intensive visual and technical checks as part of our QM documentation. We confirm the device got factory-calibrated.