Inhoudsopgave
Advertenties
2) Connect the DMX OUTPUT (3) to the DMX
GB
input of the following DMX unit. Connect the out-
put of this DMX unit to the input of the following
DMX unit etc. until all DMX-controlled units
have been connected in a chain.
3) To prevent interference in signal transmission,
in case of long cables or a multitude of units
connected in series, terminate the DMX output
of the last DMX unit in the chain with a 120 Ω
resistor (> 0.3 W): Connect a corresponding ter-
minating plug (e. g. DLT-123 from "img Stage
Line") to the DMX output jack.
5.2.2 Setting the DMX start address
For separate control of all DMX units connected to
the light controller, each unit must have its own
start address. Example: If the first DMX channel of
the spotlight is to be controlled by the DMX con-
troller via DMX address 17, set the start address 17
on the spotlight. All other DMX channels of the
spotlight will be automatically assigned to the fol-
lowing addresses (i. e. 18 and 19 in case of start
address 17).
1) Press the button MENU repeatedly until the dis-
play indicates
2) Press the button ENTER: The start address
adjusted (
3) To set the desired address, press the buttons
UP and DOWN. Now the spotlight can be oper-
ated with the light controller.
Note: When the display indicates the menu item
or
and DMX signals are present at the DMX input (1),
the dot at the right end of the display will flash.
5.2.3 DMX channels and functions
DMX
DMX
channel
value
1
000 – 255
000
2
001 – 250
251 – 255
000 – 010
3
011 – 255
Ž
DMX channels
5.3 Temperature indication
and overheat control
The spotlight is equipped with an overheat control.
When the temperature inside the spotlight is too
high, the spotlight will be switched off. After cooling
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
10
.
...
) will be indicated.
Function
brightness 0 % © 100 %
response of brightness control
low response
response very slow © fast
immediate response
stroboscope off
stroboscope slow © fast
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
®
down, the spotlight will be switched on again auto-
matically. To indicate the inside temperature:
1) Press the button MENU repeatedly until the dis-
play indicates
2) Press the button ENTER.
3) When
ENTER. The inside temperature will be indi-
cated in °C.
4) To exit the menu branch, press the button
MENU.
6 Cleaning the Spotlight
Clean the plastic filter in front of the LEDs at regu-
lar intervals or as required. This is the only way to
ensure that light will be radiated at maximum
brightness. Before cleaning, disconnect the
mains plug from the socket. Only use a dry, soft
cloth and a mild detergent. Then carefully wipe the
plastic filter dry.
For cleaning the other parts of the housing, only
use a dry, clean cloth. Never use any fluid; it may
leak into the spotlight and damage it.
7 Specifications
Data protocol: . . . . . . . . . . DMX 512
Number of DMX channels: 3
Light source: . . . . . . . . . . . white COB LED
,
Power consumption
PARC-56 / WS: . . . . . . 50 W
PARC-64 / WS: . . . . . . 100 W
Beam angle: . . . . . . . . . 60°
Colour temperature: . . . 5600 K
Power supply: . . . . . . . . . . 230 V~ / 50 Hz
Power consumption
PARC-56 / WS: . . . . . . 60 VA max.
PARC-64 / WS: . . . . . . 160 VA max.
Dimensions
PARC-56 / WS: . . . . . . ∅ 185 mm × 210 mm
PARC-64 / WS: . . . . . . ∅ 220 mm × 260 mm
Weight
PARC-56 / WS: . . . . . . 2.5 kg
PARC-64 / WS: . . . . . . 3.2 kg
Subject to technical modification.
.
is indicated, press the button
Advertenties
Inhoudsopgave
