Inhoudsopgave
Advertenties
HSG9583 Series | Instruction Manual | Installation
4
INSTALLATION
CAUTION: These units must be properly
and securely mounted to a supporting
structure capable of sustaining the unit
weight. Use care when selecting mounts or
pan/tilts (not supplied) for installation; the
mounting surface and unit's weight should be
carefully considered.
4.1
Tools Required
•
Small flat blade screwdriver
•
Phillips screwdriver (#1)
•
Adjustable wrench
•
Wire cutter/stripper/crimper tool
4.2
Cable Requirements
Video Transmission (Coaxial)
Cable Type:
RG-59/U for runs < 300m (1000ft)
RG-11/U for runs < 600m (2000ft)
Cable Size:
Outside diameter between
4.6mm (0.181in)-7.9mm (0.312in)
Cable Shape:
Round
Shield:
> 93% Braided copper shield
Center Conductor:
Stranded copper center
DC Resistance:
< 15Ω/1000 (RG-59/U)
< 6Ω/1000 (RG-11/U)
Cable Impedence:
75Ω
Agency Rating:
UL
Environmental:
Outdoor rated
Temperature Rating: > 80°C
Sources:
Belden 9259
Input Power Cord - North American
Cable Type:
SJTOW rated
Cable Size:
Outside diameter between
4.3mm (0.170in)-11.9mm (0.470in)
Cable Shape:
Round
Conductors:
3-conductor version and
2-conductor version
Agency Rating:
UL/C.S.A., UL VW-1
Environmental:
Outdoor rated
Temperature Rating: 105°C
Voltage Rating:
300 V
Sources:
Belden 19509, 3-conductor
Northwire FSJT183-81K, 3-conductor
Bosch Security Systems | 12 August 2005
All manuals and user guides at all-guides.com
Input Power Cord - European
Cable Type:
Cable Size:
Cable Shape:
Conductors:
Agency Rating:
Environmental:
Sources:
Lens Control Cable
Cable Type:
Cable Size:
Cable Shape:
Shield:
Conductors:
No. of Conductors: 4 and 8
Conductor Insulation: Color coded
Sources:
4.3
1.
2.
4.4
1.
Figure 1: Unlatching the Cover
NOTE: If the optional tamper-resistant screws have
H05RN-F 3 G 0.75 and
H05RN-F 3 G 1.00
Outside diameter between
4.3mm (0.170in)-11.9mm (0.470in)
Round
3-conductor version and
2-conductor version
VDE
Outdoor rated
Olflex rubber cable 1600 252
Olflex rubber cable 1600 253
Jacketed multiconductor cable
Outside diameter between
4.3mm (0.170in)-11.9mm (0.470in)
Round
Overall shielding
Stranded 20 to 16AWG wire
Belden 9552, 4-conductor
Belden 9554, 8-conductor
Housing Mounting
Use the two 1/4-20 x 0.50in. screws and
1/4in. spring washers provided in the hardware
kit to mount the housing to a mount or a
pan/tilt. The spring washers must be used for
the screws to thread properly.
The outermost set of 1/4-20 threaded holes are
for mounting to feed-through mounts and the
innermost 1/4-20 holes are for mounting to all
other mounts and pan/tilts.
Opening the Cover
Open the cover by unlatching the two clasps
on the side of the housing (see FIGURE 1).
been installed, use the supplied wrench to
remove the screws before opening the latches.
EN | 6
Advertenties
Hoofdstukken
Inhoudsopgave
