Inhoudsopgave
Advertenties
Automatic operation
Switch on the device as described above. The device is in automatic operation immediately after it is switched on. After
approx. 2 minutes of operation, the measurement of the air quality in the room is completed and, depending on the air
pollution, the status LED
purifier adjusts the speed of the built-in fan and automatically increases or decreases it for optimal air flow.
During automatic operation, the complete speed button
Ionization
After switching on the product, the unit automatically starts the ionization process. The ionization key
Ionization in this context means that free electrons are attached to an electrically neutral particle in the air, creating a
negative ion (anion).
An increased concentration of anions in the air can have a positive effect on the immune system, prevent fatigue and
exhaustion, improve sleep and increase general well-being. In addition, released electrons bind to positively charged
suspended particles such as dirt particles, fine dust, smog or pollen in the air. Electrons and suspended particles then
combine to form larger molecules that are heavier and sink to the ground. From there, they can be removed more easily
than regular dirt particles from the air.
To stop ionization, press either the ionization button
UV sterilization
After switching on the product, the UV sterilizer downstream of the filter
the cleaning effect of the air filter and helps to eliminate germs, viruses and bacteria.
The UV sterilizer is active in 20-minute cycles, each with a 10-minute interruption, but for no longer than 4 hours. After
that, the function switches off automatically. To end the function manually, press the UV On/Off button
control.
Manual operation
Switch on the device as described above. The device is in automatic mode immediately after it is switched on. After
approx. 2 minutes of operation, the measurement of the air quality in the room is completed and, depending on the
air pollution, the status LED
of the built-in fan yourself, press either the speed button
To switch back to automatic operation, press the mode button
lights up blue.
16
Adjusting the speed
If you are in manual mode, you can set the speed of the fan yourself at any time. On the device, you can select the speeds
„Lo" (Low), „Mid" (Medium) or „Hi" (High), or switch the device to Sleep mode or Auto mode by pressing the speed button
several times. On the remote control, press the fan button
16
Depending on which speed level is set, the respective area of the speed button
lights up:
„Lo":
low speed
„Mid":
medium speed
„Hi":
highest speed
In manual mode, the speed is not automatically adjusted should the air quality in the room change, even if it is indicated
by the status LED
.
8
Sleep mode
First switch the unit to manual mode by pressing either the speed button
remote control. Press the button or knob again until the text „Sleep" on the speed button
panel
.
9
The unit is now in Sleep mode and then operates extremely quietly at the lowest speed level. In sleep mode, the speed
of the built-in fan is lower again and the illumination of the status LED
Press the speed button
16
light up again as usual and the set speed is displayed.
Timer
The unit has a timer function that allows you to select the operating time from four different times. To do this, press either
the timer button
on the device or the timer button
15
you press the button again, the timer time increases. The set duration lights up blue on the control panel
1 h (one hour) - 2 h (two hours) - 4 h (four hours) - 8 h (eight hours).
During the operation with timer, the respective display of the operating time also changes. After the time has already
elapsed (1 hour, 2 hours, 3 hours, 4 hours, 5 hours, 6 hours, 7 hours), the display changes to the respective remaining
time. When the timer has expired, the device switches off automatically.
While the timer is activated, all other functions of the device can still be used and set. The timer remains unaffected.
lights up either blue, green or red. Depending on the level of air pollution detected, the air
8
lights up either blue, green or red. To switch to manual mode and determine the speed
8
or the mode button
again to exit the sleep mode. The displays on the control panel
21
on the control panel
16
on the unit or the ionization button
17
2
on the device or the fan button
16
on the remote control until the complete speed button
21
several times to cycle through the different speeds.
22
16
can be switched off, if desired.
8
on the remote control to set the timer to 1 hour. Each time
19
13
USER GUIDE
is illuminated.
9
on the remote control.
20
starts automatically. This further increases
on the remote control.
22
on the control panel
16
on the unit or the mode button
lights up on the control
16
lights up blue.
17
on the remote
24
on the unit
9
on the
21
then
9
each time:
9
Advertenties
Inhoudsopgave
