Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Operation of the sander
Choose the appropriate tool for a given operation mode. Before starting work, you must allow for grinding wheel to reach its full speed. Only the
rotating grinding wheel should be applied to a workpiece.
You should apply only such pressure to the tool, which is required for the material processing. Too much pressure can damage the grinding wheels
and increase the risk of injuries.
During work the sparks can occur and workpiece fragments of the workpiece can tear off . You should ensure that sparks and tear-off fragments
would not create risks in the workplace.
MAINTENANCE
Never use gasoline, solvent, or any other fl ammable liquid to clean the tool. The vapors can be ignited, causing the tool explosion and serious injury.
Solvents, which are used to clean the tool holder and the body, can cause seals softening. Thoroughly the tool before starting your work.
In case of fi nding any irregularities in the tool operation, the tool you should be immediately disconnect from the pneumatic system.
All the elements of the pneumatic system must be protected against contamination. Contamination, which entered the pneumatic system can
damage the tool and other air system components.
Maintenance the tool before each use
Disconnect the tool from the pneumatic system.
Before each use, let a small amount of liquid preservative (e.g.. WD-40) through the air intake.
Connect the tool to pneumatic system and run for about 30 seconds. This will distribute the liquid preservative inside the tool interior and will clean it.
Again, disconnect the tool from the pneumatic system.
Let small amount of oil SAE 10 to the inside of the tool, through the air inlet and the holes intended for this purpose. It is recommended to use oil
SAE 10 intended for maintenance of pneumatic tools. Connect the tool and run it for a short time.
Attention! WD-40 may not be used as an appropriate lubricating oil.
Remove excess of oil, that spill out through the holes. Left oil may damage the tool seals.
Other maintenance operations
Before each use, you should check whether the tool shows any traces of damages. Drivers, tool holders and the spindles must be kept clean.
Every 6 months or after 100 hours of operation, you must pass the tool for inspection by the qualifi ed personnel in the repair shop. If the tool was
used without the application of recommended air supply system, you should increase the frequency of the tool inspections.
Troubleshooting
You should stop using the tool immediately after the disguardy of any fault. Work with a defective tool can cause injury. Any repair or replacement
of tool components must be carried out by qualifi ed personnel in authorized repair facility.
Failure
Possible solution
Let a small amount of WD-40 through the air inlet. Run the tool for a few seconds. The blades may stick to the rotor. Run the tool for about 30
The tool has too slow
seconds. Lubricate the tool with small amount of oil. Attention! The excess of oil can cause a decrease in power of tool. In this case, you should
rotations or it does not start
clean the drive.
The tool starts and then
The compressor does not provide proper air supply. The tool starts by the air collected in the tank of compressor. As the tank is emptying, the
slows down
compressor has not kept pace with the refi lling of air shortages. Connect the device to a more effi cient compressor.
Make sure that your hoses have an internal diameter of at least such as specifi ed in the table in point 3. Check the set point of pressure, whether it
Insuffi cient power
is set to the maximum value. Make sure that the tool is properly cleaned and lubricated. In the absence of results, submit the tool for repair.
Worn tools are secondary raw materials - it is forbidden to dispose of them together wigh household waste, because they contain substances
harmful to human health and the environment! Please actively support the cost-eff ective management of natural resources and environmental
protection by passing the used equipment to the point of storage for worn out devices. To reduce the amount of disposed waste it is necessary to
re-use them, recycle or recover in another form.
O R I G I N A L
16
EN
I N S T R U C T I O N S
Advertenties
Inhoudsopgave
